Turning relay VAZ-2110: location and function. Spare parts for VAZ-2110

The car is equipped with light devices, which are necessary for safe movement on the road and driving in the dark. Turners are one of the most important light signals. It is used to indicate when rebuilding, as well as the inclusion of an alarm. Quite often, the relay turns VAZ-2110 out of action. This happens for various reasons, which we'll talk about in this article.

About fuses and relays

The machine is equipped with a fuse box, in which they are installed in large quantities. Each of them is responsible for here or another function. If the fuse blows, the turn signal light may not work. This, of course, applies to all electronic systems, but we are interested in these.

A fuse is used to protect against overloads. If the circuit has problems, say too high voltage, then the fuse blows. Consequently, the chain is washed on it, and the voltage does not come on. It turns out that the same turn signal will not function without a fuse, which is quite logical.

Where is the turn signal relay on VAZ-2110

If the car is not working, the first thing to do is check the fuse box, because that's where the reason often lies. Could trivially fuse the fuse or the relay failed, which happens less often, but it does happen. Find on the "top ten" this unit is quite simple, it is located next to the lever opening the hood. The relay-breaker is located in the slot K-3. It is responsible for the operation of turn signals and alarms. The burnt out fuse is extremely easy to locate, it is usually determined visually and changes to a new one. There is nothing complicated. If the problem with the relay, then in most cases it makes no sense to repair it. It's much easier to buy a new one and be sure that it will not refuse in the near future.

Malfunctions and their elimination

There are several ways to understand that the relay is going wrong. First, pay attention to the frequency of the relay clicks. In case of burnout of one of the bulbs, the relay will blink twice as fast. When there is no signal at all, it's worth checking the wiring, maybe it's in it. Culprit can also be a fuse. The fault must be started from the state of the electrical circuit. It is due to the fact that oxidized contact or short circuit leads to a lack of signal or increased voltage. Just so fuses and relays do not burn out, so the problem is most often in the wiring. If everything is in order there, then we change the fuse and, if necessary, a relay. You can do this by removing it from the brackets in the mounting block. Then we put a new detail, and all should earn.

In brief about the status of the posting

Usually the car is operated for a long time without any maintenance in terms of electricians. Burned light bulbs and fuses change, and the wires remain unattended. However, this is wrong. It is necessary to periodically clean the oxidized contacts and change the broken wires or, in extreme cases, solder them. This will ensure a reliable signal and a long operation of the electronic devices of the car.

If the part has already failed, first you need to determine which relay of turns on the VAZ-2110 is installed. The easiest way is to take the old one and go with him to the store. Although usually it is enough to ask the relay to "ten", and the seller will give you the necessary detail. But it's better to be safe.

Buy quality spare parts for VAZ-2110

Often the acquisition of frank "Chinese" leads to breakdowns. This does not apply to fuses and relays, as to the parts of the chassis and engine systems. That is why it is strongly recommended to purchase a store in specialized stores for classics. You can make an order through the Internet, which allows you to choose the manufacturer and the delivery time.

Of course, this is more the case with foreign cars, which are not in every store you will find spare parts. But it happens, and it's hard to find any detail on the "top ten". Such spare parts on the VAZ-2110 as relays and fuses are worth a penny, and you do not need to save on it. Always have spare fuses.

If it's not a relay

It also happens that the usual replacement of fuses does not help. The wiring was checked, the relay was replaced, but still nothing works. In this case, it makes sense to pay attention to the status of the stalk switch. There are several "sick" places where the solder of the contacts is weakly held. Because of this, turn signals can stop working. In this case, you need to remove the stalk switch, find faulty contacts and solder them. There is nothing complicated here, only the ability to handle a soldering iron is important. If the VAZ-2110 turn switch is clicked when it is turned on, then the system is OK. The dummy switch itself will cost you much more, so be careful when dismantling it and installing it, try not to damage the connections and contacts.

A few important details

The most annoying situation is when the entire fuse block breaks down. In this case, you can try to reanimate it. For this, it must be removed and disassembled. Check the integrity of all contacts and cards. If necessary, solder damaged areas. But when there is no such opportunity, it is easier to buy it. The main thing is not to be mistaken with the choice of the model, since the assembly blocks are of several types depending on the year of manufacture of the car. The block of the old sample will not be replaced by a new one, and vice versa, too, will not work. In this case, it is also advisable to bring all the accessories to the store, so as not to be fools.

As you can see, it's quite easy to determine where the turn relay on the VAZ-2110 is located. To do this, you just need to carefully look at the diagram presented in this article. It clearly shows its location.

Logical completion

If you are not looking for simple ways, you can try to disassemble the relay itself and check what's wrong with it. Maybe the movable plate is acidified or the contact has moved away. Since the element is small, one must be very careful and do not bend anything. Using a small soldering iron, as well as fine-grained sandpaper, you can bring the relay to life and at the same time get a precious experience in repair.

Replacement of the rotation relay VAZ-2110 is quite simple and fast. There is absolutely nothing complicated, so it makes sense to perform such work independently. This does not require you to know electrical engineering. The relay itself can "bug" if its time is right. When the first signs of malfunction have appeared, such as a periodic relay failure, a changed frequency of clicks, etc., it is better to stockpile the spare part in advance. So, if necessary, you can immediately replace the VAZ-2110 turntable relay.