Ready-made pattern of a woman's windbreaker. Women's windbreaker with their own hands

Today, women's clothing stores have such a wide range that it may seem that the sewn women's windbreaker with their own hands, whose patterns will be discussed in this article, is an absolutely unjustified occupation. However, if you think about it, you can find a lot of advantages and advantages of self-tailoring.

First of all, this is economy. As a rule, sewn things cost several times cheaper. Also, do not forget that, by modeling the style, you can take the most liked details of various models and put them together in your product. Well, the most important thing is the color and size, which, as practice shows, can be very difficult to find when choosing a ready-made jacket. That thing is great, it fits perfectly to the color of the eyes, but it is not enough, it is perfectly seated, but the shade does not satisfy the requests in any way. So it turns out that in a huge assortment of fashion stores you can lose several hours of time and still not find the right option.

Whether it's for self-tailoring! Especially since the design of the female model's windbreaker is very simple, and even the most inexperienced craftsman can sew it.

Removing measurements

Sewing of any clothing begins with the removal of measurements. The design of the female or male windbreaker is based on basic measurements: waist, hip and chest girth, shoulder width, sleeve length and product length. This thing is different from other women's outerwear in that it does not make darts on either the chest or waist, which greatly facilitates the construction of the template and minimizes the number of measurements taken from the figure.

Building a Shelf Template

To build a template, you need a newspaper, glued sheets of paper or building film. They will need to identify the boundaries of the drawing. It should be a rectangle with sides that will correspond to the semicircumference of the chest + a few centimeters to fit freely (the amount depends on the style), the other side should be equal to the length of the product from the shoulder to the bottom.

The female pattern of the female model on the drawing is constructed as follows:

1. At a distance of 25-30 cm (and for large sizes 35-40 cm) from the upper side of the rectangle, a parallel line is drawn, which is referred to as the breast line.
2. Then divide this straight line into parts: the width of the back, the zone of the armhole (the size of the half-chest is divided by 4 and added 2 cm), the area of the front shelf.
3. Then proceed to the neck in the upper corners of the rectangle. Depart from the corner in the direction of the rectangle of 6 cm and deepen the neck on the back by 5 cm, and in front by 5-6 cm.
4. Further from the extreme points of the neck mark the shoulder seams, underestimating them by 1.5 cm from the upper side of the boundary of the drawing.
5. Then they find the middle of the armhole on the chest line and lower the straight lines from the edge of the shoulder slices. After they paint the armhole, rounding the corners.
6. If the length of the product is higher than the hips or the measurement of the hips is analogous to the breast, then all the constructions on this can be completed. If the hips are wider, it is necessary to take into account the difference and flare the lateral cut, descending from the midpoint of the armhole perpendicular to the lower boundary of the drawing.

Thus, as a result of all manipulations, a pattern of the female jacket of the windbreaker, or rather, the halves of the backrest and transfer patterns, will be obtained. Next, you should begin to develop a sleeve.

Sleeve construction

The finished pattern of the female windbreaker should consist of the back half, the front shelf and the sleeve. Different cutters use different methods of constructing the sleeve, but the principle is always the same: the pellet must perfectly fit into the armhole on the front and back. To build this element, you should already have the ready-made templates of the shelves aligned on the shoulder seams and transfer the armhole line to a separate sheet. Then the rounding at the shoulder should be closed in a circle. At its lower boundary, place the center of the measure "the width of the upper part of the hand. On the top - to retreat upwards of 1.5 cm and smoothly reduce the curvature from this point to none. Further, it remains only to delineate the line of the pellet and to make a control measure of compliance with the length of the cut of the armhole.

Hood and collar construction

The pattern of a female windbreaker with a hood differs only in that, in addition to shelves and sleeves, a template for the hood should be developed. Make it simple enough. It is necessary to measure the circumference of the head and measure the length from the forehead and to the nape through the crown and the height of the hood (from the shoulder to the top of the head). The construction is made in a rectangle, where the sides are equal to the height of the hood and the semi-grip of the head.

The measure taken from the forehead and to the occiput should be laid through one of the upper corners of the rectangle, the sharp edge should be rounded, and the forehead area should be dropped 1-2 cm. In the region of the occipital cut, the line should be moved 3-4 cm inwards Rectangle. The hood base line, along which it will connect with the windbreaker, should be made curved. At the nape - raised by 3 cm, and to the face, on the contrary, dropped. This will ensure the correct fit of the hood and eliminate unnecessary folds on the back of the head.

The collar is much easier to make. It will require a strip of fabric equal to the double height and width corresponding to the cut of the neck.

Fashion Modeling

The main pattern of the female model's windbreaker is already half the battle. Everything else is just a detail. At the modeling stage, the arrangement of pockets, patches of decorative elements and other shaped elements is being studied. By the way, pockets can be slotted on a lightning or overhead, as well as a combination of some with others.

By this description, you can sew absolutely different models. Do you need a large women's windbreaker? The pattern, the description of which is presented above, perfectly suits absolutely for any complexion. Slightly crumble the bottom, add cushers and cords along the sides to add side seams, similar to the design of sleeves and collar - and an excellent windbreaker for the lady of magnificent form is ready.

Elasticated cuffs

Vetrovkam characterized by cuffs at the bottom of the product and on the sleeves. For their registration, you can take special knitted dovetails or a fabric hem or, using the basic fabric and a wide elastic band, make these elements yourself. A strip of fabric for the length of the stretched rubber band and its double width, embedded inside the elastic band, stitched through every half a centimeter - and the cuffs are ready.

A little about the choice of fabrics

The most successful material for a windbreaker is a plaschevka. This material protects well from the wind and can withstand a small rain. If for the product to take a warm fleece, then the pattern of the female model's windbreaker miraculously turns into a warm and cozy anorak.

It will also look good with a leatherette or a leather lacquer. However, the choice depends on your own preferences and taste.

Working with a lining

If you sew a windbreaker without a lining, it will be an excellent option for cool summer evenings, but if you need a warmer model, it's better to decorate the lining, or you can even use a quilt with a small layer of sintepon.

To cut the lining fabric, you will need the same pattern of the female model's windbreaker. First, collect all the elements of the top of the product, then completely sew up the lining, and then connect them.

The sequence of assembly is as follows: first along the neck and anterior incision; Further on the bottom, and then in the sleeves.

To ensure that all junctions are beautifully decorated, they are sewn through an opening in one of the sleeves. In the last turn sew up the sleeve.