Installation of windows in a wooden house with their own hands

Choosing a wooden house, property owners prefer environmentally friendly housing from natural building materials. Many owners use natural materials to further design the exterior and interior of the house. Installation of windows in a wooden house is one of the most important components of the entire construction process.

Contrary to the prevailing stereotypes, many homeowners consider it logical to install wooden windows in a country -house timber house . This allows you to rest from the constant contemplation of plastic and metal, gives a special peace to the room.

Wooden windows, in contrast to the metal-plastic constructions, have the same expansion factors as the walls. Thanks to this, the installation of windows in a wooden house can be done with minimal gaps.

Lacquers on a water basis reliably protect the tree from not always favorable environmental influences. A wide range of paint and varnish coatings allows you to choose the shade of wooden windows for the style of the house. Often the most appropriate to preserve the natural color of the tree, using colorless varnishes.

Installing windows in a wooden house is a time consuming process. Each landlord wants windows to be installed qualitatively and for years to come. Therefore, in most cases, the installation of windows is trusted by professionals, although the installation of wooden windows with their own hands is also possible.

To install windows in a wooden house was done without errors, you need to know some installation rules. The technology of installing windows involves knowing and performing the following actions / recommendations.

1. In the event that the windows are replaced, it is necessary to dismantle the old window blocks. If necessary, cut the old box. Window aperture to clean (remove the debris (a patch, a heater, an old plaster)), dismantle the windowsill.
2. Check the conformity of the new window unit. Examine the product, make sure there are no defects, check the correspondence of the window dimensions to the dimensions of the opening.
3. If there are opening flaps, remove them.
4. Secure anchor plates or drill holes, according to the measuring sheet, GOST, type of house. The distance from the inner corner of the window box to the fasteners should be 15 -18 cm, and between the fasteners - no more than 80 cm. It is customary to install no more than 2 fasteners on one side of the window block.
5. If necessary, it is necessary to cover the frame with a special tape PSUL (pre-compressed sealing tape). If it is not used, then it is necessary to provide a gap between the quarter and the frame (5-20mm). At the end of installation, this gap must be filled with a sealant.
6. Installation of windows in a wooden house must be carried out according to the level. This is required for good sealing and proper operation of the locking mechanisms.
7. Fasten the lower and upper parts of the window unit using anchor plates or dowels. Conduct a control measurement of deviations, which should not exceed 1.5 mm per 1 m (both vertically and horizontally). Exceeding the permissible norm of deviations can significantly affect the durability of the insulating glass unit.
8. With the help of mounting foam, seal the installation joint between the wall and the frame. In the event that the installation of windows in a wooden house is done without a PSUL tape, seal the seam on the outside with a sealant. This makes it possible to improve the thermal insulation characteristics.
9. Install the drain (drainage profile), fixing it from the outside of the frame with screws. To improve thermal insulation and eliminate noise when rain falls on the ebb, fix it with a foam sealant (mounting foam).
10. Hang the sash and install the opening handles. If the installation of windows in a wooden house was made using anchor bolts, they should be covered with decorative caps.
11. Install the window sill with support technological wedges. Fix it with foam sealant.
12. If necessary: install slopes, trim for windows, adjust fittings.

Incorrect installation of window blocks can lead to a change in the geometry of the window, the sagging of the flaps. As a consequence - the work of the locking mechanisms is broken, opening and closing the valves is difficult.

The quality of windows is checked by time, so when buying and installing windows in a wooden house, you should carefully consider the choice of the manufacturer, paying attention to the reputation, the level of service and the duration of the work in the market of window technologies.