How to make a speaker yourself?

We will analyze in this article everything that is somehow connected with the speakers: how to make your homemade device (including the speaker from the speaker), how to increase their volume on the computer or headphones, how to make a podium for them.

Speaker yourself: the first way

Before you make the dynamics yourself, prepare the necessary materials:

• paper;
• permanent magnet;
• Aluminum scotch or wire;
• A stapler;
• scissors.

Making such a simple speaker is very easy:

1. Cut thin strips of aluminum tape.
2. On a square sheet of paper, glue these pieces "snake", nowhere touching and crossing them. In the same way, you can also glue the wire with a spiral. Attach it can be pieces of ordinary scotch.
3. With a stapler, secure the sound device with aluminum strips or wires. It is good, if the wires are bare.
4. Bring a permanent magnet to the paper and turn on the sound on the device. Done!

Homemade speaker: the second way

How to make a speaker in this case? Prepare:

• Paper;
• Copper wire;
• Paraffin or rosin;
• A magnet of cylindrical shape.

An instruction that tells how to make a speaker:

1. Glue a small cone from the paper.
2. Scratch the paper tube - it should be slightly lower and wider than the cylinder magnet. Glue this part to the base of the cone.
3. Insert a magnet into the tube.
4. Wrap the tube with a magnet with a thin wire - the more turns you have, the better the sound.
5. Pour the paraffin or rosin wire so that it sticks to the paper with the magnet.
6. Fasten the position of the cone to the surface, gluing it with her folded accordion strips of paper.
7. At this point, connect the ends of the wire to the amplifier and enjoy the music.

How to make a speaker column?

If you want to get a high-end column as a result, then you need three dynamics: high-, medium- and low-frequency. The case for it needs to be made strictly rectangular. Let's consider its production in stages:

1. First, prepare the case - it can be based on chipboard, plywood, board thickness of 10-12 mm.
2. Cut the front, back and side walls with a carpentry tool / saw / electric jigsaw. Do not forget to make three holes in the front corresponding to the speakers - at the top there will be a high-frequency one, in the middle - a mid-frequency one, at the bottom - a low-frequency one.
3. For best sound, install a rubber tab between the wall and the speakers, and cover the inside with felt.
4. Secure the assembled body with superglue and screws, leaving the back section loose.
5. At this point, lead to all three wire drivers and output the terminals to the outside of the rear wall. Connect the speakers to each other in parallel.
6. After you have sorted out the wiring, close the case with the back wall and secure it with the same screws and glue.
7. If your column turned out to be larger, then you need to take care of inserting the stiffeners - they will help to avoid unpleasant rattling of sounds. In addition, you can attach rubber feet to the body.

How to make podiums for speakers?

In the manual, we'll look at how to make a podium for any speaker and car:

1. Decide on the shape of the future podium - the design should not interfere with the handle of the power window and the car door closing. Draw the project on the cardboard and cut out the pattern on its outline.
2. Now you need plywood thickness of 6-8 mm. Sample two parts.
3. At this stage, you need to engage in a platform for the speaker - the base in the form of a ring. The diameter of the inner circumference of the platform must coincide with the internal diameter of the seat, and the diameter of its outer circumference - with the diameter of the protective grid of the speaker. To get an aesthetic appearance of the future podium, add to the outer ring 5-7 mm - this is necessary to install the decorative ring.
4. Draw also on the cardboard the template of the base and the decorolc. Transfer the contours to the plywood and cut out these details.
5. Spread the decorative ring with glue and secure it on the ring-base.
6. At this point, attach the ring to the main part. This is most easily done with spacers providing rigidity of fastening, because the speaker will be tilted and will be protruded forward. Spacers are made of ordinary racks.
7. Now you need to set the form for the podium - the best assistant here is the mounting foam, because with this material you can give your design any shape. In order not to spend foam on the hole of the ring (where it still has to be cut), put a suitable size bottle, pipe, etc. Be careful - the level of the dried foam should not be below the level of the ring.
8. With a sharp clerical knife, give the dried foam surface the shape you need. After that, grind it off with a large "sandpaper".
9. To make the surface perfectly smooth, prepare a mixture of PVA glue and putty, apply it in thin layers and leave to dry. Then treat the product with a "sandpaper".
10. At this point, soak the product with a protective layer of epoxy resin. Next - a layer of fiberglass, and then - all of the same resin. Extra pieces after drying are also cleaned with sandpaper.
11. The last stage is the stretching of the podium with artificial leather. Pull the material from the ring to the edges, simultaneously cutting off excess and fixing the skin with a stapler.

Increase the speaker volume on your computer

So, how to make the speaker louder on Windows:

1. Right-click the volume icon in the tray.
2. In the pop-up window, select "Playback Devices".
3. Next, select the desired speakers, click on them again PCM, click on "Properties."
4. In the menu that appears, you will need the "Improvements" tab.
5. Check the "Equalizer".
6. Next, find the "Sound effect properties" section. Opposite the line "Setting" click on the button with three dots "..."
7. In the drop-down menu, lift all the sliders up, save the result.

If as a result of this operation, the dynamics began to "croak", then go back to the sliders and lower to the previous level the first 2-3.

Increase the speaker volume on your smartphone

How to make the loudspeaker louder on your gadget? Read lifhak further:

1. Call up the engineering menu of your smart. On how to do this, in most cases tells the complete instructions on the official website of the device manufacturer. The most common command: * # 9646633 #.
2. Next, you need to stop on the "Audio" - select the type of sound that you do not like, - "Loudspeaker", "Speaker for conversation", "Headphones".
3. By selecting any of the three items listed above, you will see the following items: "sound", "melody", "speech", "microphone", "keyboard tone".
4. Clicking on any of the items, you will notice seven loudness values - from 0 to 6. To make your speaker louder, you need to select "6".
5. The maximum value is 255. However, be careful when selecting a figure greater than 236, - this can lead to a rapid breakdown of the speaker.
6. Agree to the changes, return to the menu and click on "Update".
7. Reboot your device - after this change must take effect.

You now know how to make a speaker yourself or increase its volume. Good luck and be careful in your experiments!