How to disassemble Acer laptop?

Before you disassemble the Acer laptop , it's important to remember that for all units of this manufacturer there is a guarantee for a certain time. If the laptop is dismantled before the warranty repair, then the entire responsibility for such actions will be assigned to the one who disassembled. In order to disassemble the laptop Acer, you need to prepare the following tools:

• Screwdrivers (flat, cross and flat plastic);
• Plastic tweezers;
• Grounding bracelet.

Before you disassemble the Acer Aspire laptop, you need to understand that there are many differently sized screws in the design. Masters, analyzing such units, follow the same rule: each bolt should be placed directly next to the component for which it is intended. Getting to work, you need to turn off the laptop from the network. It is also necessary to separate all cables and remove the battery.

Disassembly is performed only with respect to the lower part of the unit. The monitor can not be disassembled in any way, because such work can only be done in the factory. If the monitor is faulty, then it is replaced entirely. This is a modular replacement, the design is unlikely to be repaired. Asking how to disassemble the Acer laptop, many users believe that computer systems are somewhat similar to television systems. However laptops are thinner devices. First of all, the battery is removed from the laptop. Following him is a stub of memory cards. Then it is necessary to remove the bolt and remove the optical drive module.

The drive module must be disassembled. To do this, remove the holder and cover plate. At the same time, there remain two bolts, which must be placed next to the module, so as not to lose. For those who do not know how to disassemble an Acer laptop, one must remember this sequence of actions. After the optical drive is removed, you can proceed to further disassembly.

The cover of the system unit in the laptop is fixed with two screws. It's time to take it off using a screwdriver. Under the cover, you will find a hard drive, a wireless network card and a memory card. The next step is to remove the 3G module. Having unscrewed the screw from the cover, it is necessary to raise it and detach the module. Next, you need to remove the memory module. If there are two modules, then both must be removed.

If parsing occurs for the first time, it is better to write down the process or memorize. Remembering how to disassemble the Acer laptop, you can then easily assemble it in reverse order. Now you need to disassemble the wireless LAN card by disconnecting the antenna cable. The board is screwed with two screws that need to be removed. It remains only to disconnect the board itself, and you can start the hard disk. The module disconnects quite easily. To remove it, there is a special label, pulling it, you can easily pull it out by unplugging it from the motherboard. The disc is removed with the holder, to which it is screwed with four screws.

Knowing how to disassemble the Acer laptop, you must also observe a number of rules, especially when it comes to the motherboard and the drive. Do not apply great force to these modules, otherwise you can easily damage the system. It's time to remove the keyboard. It is fixed on top of the latches. Having unfastened them, it is necessary to bend the keyboard and remove it. You can see the cable of the device that needs to be removed. To do this, disconnect it from the motherboard.

After that, proceed to the top panel. It is attached to the 4 screws in the area of the battery recess and 11 on the bottom. Unscrewing each one, you must carefully remove the panel. To do this, you still have to carefully disconnect the motherboard cables by lifting the latches. At this stage, you can already detach the top of the case from the bottom. Now it only remains to remove the components one by one, the most difficult work behind. Before you disassemble the Acer laptop into two parts, you need to determine if there is room for decomposing all the components. Otherwise, they can get lost. From the top part are removed: speakers, power supply, touchpad, card reader, USB - card, Bluetooth module. Next, the motherboard is removed. It is important to remember that you can not completely remove it.