Facade lift: technical characteristics, advantages and application features

Repair of high-rise buildings is not so easy. Such work always carries a risk to health and life. However, there are devices with which you can carry out all actions quickly and efficiently. One of them is a facade lift.

Benefits

Among the advantages of adaptation are:

- Ability to perform work of any complexity.

- Multiple uses, and, therefore, the duration of the service.

- Multifunctionality.

- Affordable cost.

- Large strength stock.

- Different sizes of the device.

- Easy to transport and use.

As you can see, the facade lift is indispensable for high-altitude work.

Applications

The presented product is intended mainly for performing repair or harvesting works at high altitude. There can be one or two people on such a platform. It has a fairly complex device. In addition, it has some technical requirements. During operation it is necessary.

Most often, a facade lift is used in construction. Thanks to him you not only can carry out repairs, but also transport construction materials upstairs. In the same way, workers can be delivered to the facility. And the device is used for welding works on bridges, ships, dams and other structures, for repair of which standard methods can not be applied.

Product design

So, the facade lift has such a structure:

1. A platform on which, in fact, a person will stand. In another way it is called a cradle.

2. Consoles on the roof of the structure, with which the platform will be suspended.

3. Cables or cables, the length of which is not less than 100 meters.

4. Counterweight, the mass of which should be about 25 kg.

5. Catchers for insurance.

Naturally, such a product should have a control panel with which you can adjust the height and position of the platform. That is, the facade lift ZLP has a simple and intuitive device.

Specifications

The device has the following features:

- Working height, which can be lifted by the device: 150 m.

- Maximum lifting capacity: about 300 kg.

- Diameter of the rope for lifting: not less than 8 mm.

- Lifting speed per minute: 5 m.

- Number of traction winches: 2

As for the dimensions of the platform, the facade construction hoist may be different.

Technical requirements for the product

The device shown can only be used if it meets the established standards. Lift facade - cradle - must comply with such technical requirements:

1. The platform for one person provides a working area of 0.7 square meters.

2. On the floor of the cradle must be present anti-slip coating.

3. If the platform is single-sided, it has only one safety and lifting rope. At the same time, the maximum load that it can lift is 120 kg. In two-suspension cradles this parameter is 300 kg.

4. Any lift must be equipped with fences. Their height must be at least 1-1,20 m. At the same time, the door in the enclosure is not provided.

5. In order for the cradle not to swing, it is necessary to attach the supports to the structure.

6. In order for the platform to move well on the ground, it is necessary to equip it with rollers.

Without observing the requirements, it is not recommended to use the lift.

Features of platform operation

In order for the application of the device to be effective and safe, it is necessary to observe certain rules for working with it:

- To start, the cradle needs to be assembled. How this is done, you can read in the instructions to the device. However, please note that all connections must be strong. You can not skip a single step during the build process. Do not hurry.

- If the platform is significantly tilted or the tension of the cables has been reduced, it must be adjusted. People can not be allowed to construct such a structure.

- The building cradle (facade lift) must be set up to perform a specific job. Only in this case you can achieve high efficiency.

- The presented technique can not be fixed with a rope. At the same time, the platform must be clamped so that the cables do not touch the projecting parts of the structure. Otherwise, they can quickly become redundant, which threatens the safety and health of workers, as well as those around them.

- Please note that during the work the temperature should not fall below -40 and rise above 40 degrees.

- Do not use the device in rain conditions. The fact is that in this case the floor of the cradle can become slippery. This factor can also threaten the safety of people.

- If the work is carried out at an altitude of 10 m or more, then the wind speed should not exceed 14 meters per second.

- During operation, it is advisable not to leave any fire and explosive substances on the platform. Naturally, if it is necessary to paint the facade, then the varnish or paint will have to be taken up. However, during work, you should be as cautious as possible.

- Workers who will work in the cradle should be additionally tied to the insurance rope. In the event of a platform breakdown, people will be able to get out of it and not die.

In any case, every technical device requires careful and attentive attitude, observance of all necessary safety rules. Good luck!