Homeliness, Repairs
Decorating arches with a decorative stone in the apartment: photo
Decorative stone acts today as one of the most suitable materials for finishing surfaces both inside and outside buildings. This material is fairly easy to process, it can not only be drilled, but also cut. But to get a good result you should follow the installation technique, it will be presented below. Use decorative stone for interior decoration, as one of the elements of which is the arch.
Preparation of tools
Decorating the arches with a decorative stone begins with the preparation of tools, among which are:
- Building mixer;
- Cutting machine;
- A bucket for mixing glutinous solution;
- Paint brushes;
- Trowel;
- Syringe for grouting;
- Wedges of the same thickness.
Among other things, you will need a building level and a spatula. It is important to worry about the presence of a metal brush and rubber kiyanka, with the latter you can customize the elements on the surface after laying. To measure and cut the material you will need a construction tape measure. Do not get by in the process of work and without a domestic atomizer. Wedges can be made of wood and plastic, they will allow to form seams. You can replace the cutting machine with a cutting machine.
Preparation of materials
Decoration of arches with decorative stone is carried out after the preparation of all necessary consumables, among them it should be noted:
- glue;
- A primer;
- Grout;
- Water repellent.
When choosing a glue, you need to pay attention to its purpose. For certain types of finishes are produced different grades of adhesive compositions, they are usually designed to hold the calculated weight of the material. Therefore, to begin with, you need to choose the finishing materials, and only then proceed to purchase glue. If the work is supposed to be carried out at low temperatures, then it is necessary to take a more serious approach to the choice of adhesive composition, it should have the appropriate properties.
Surface preparation
Decorating the arches with a decorative stone necessarily involves the preparation of the walls. To do this, you need to rid the base of the old whitewash, wallpaper or paint. The master has to align using a putty. The surface of the arch must be primed, this composition will fix the fine particles among themselves, so any finish will be held as tightly as possible.
On sale you can find primers for any surfaces. If you want to work with a concrete wall, then it should be treated with "Concrete contact" primer. When the conditions in the room are high humidity or temperature, the back side of the decorative stone should be soaked before laying.
Recommendations for finishing stone gypsum plasterboard
Decorating the arches with a decorative stone is carried out on a slightly different technology, when it comes to the construction of gypsum board. Prepare for such work requires a light stone. Such manipulations must be carried out only indoors. If the arch from the GKL is in the open air or under a canopy, then decorate it with a stone can not.
The surface of drywall is treated with a primer, which should be left until the time of drying, only after you can start to install products. Primer is applied by roller, and not only external but also internal surfaces are processed by the composition.
Stone preparation for laying
If you are to decorate the arches with a decorative stone (photo designs are presented in the review for your reference), for the beginning it is recommended that all products from different packages be mixed first. At the next stage, the stone needs to be spread out on the floor. The position of the individual elements is chosen in such a way that the invoice looks most advantageous. For example, you can distribute the elements in shades or shapes, as well as in dimensions.
Rules for applying glue
Before starting work, it is necessary to read the instructions and dissolve the glue in the bucket according to it.
The glue is applied to the entire surface of the stone, while avoiding voids, which can cause condensation inside the masonry during operation. This recommendation applies to walls, on their surface the adhesive must be applied evenly.
Technique for the installation of decorative stone
When finishing the arch with decorative stone in the apartment, you need to follow certain instructions. The stone is applied to the place treated with glue and pressed against the surface. It is important to use the building level, and with the help of the kyanki, the products are aligned vertically. The stone can be moved from side to side to achieve its close fit to the surface.
In order to check the quality of the masonry, during the installation it is necessary to tap the products with a handle from a screwdriver. This will make it clear whether there is a void inside. If there are any, the stone is removed, cleared of the glue, and the work is repeated anew. When the decoration of the arch is done with a decorative stone in the apartment, you should definitely consider the photo. They will allow you to understand what material is better to prefer. Once the finish was on the wall, you need to tap it gently on the wall, the adhesive is removed using a spatula. If the mixture appeared on the ends, it is not necessary to remove it, it will improve the quality of the adhesion of the material to the wall. You can carry out the work according to one of two technologies:
- Without seams;
- With a screed.
Stacking of stone with seams
When the arch is decorated with a decorative stone with your own hands, you can form seams between the products. Their grouting is carried out with the help of a syringe, filled with grout. The solution should be applied in such a way that it is 4 mm deep from the outer edge of the product. This will form a clearly expressed relief. To obtain a smooth texture, it is necessary to fill the seam at one level with the face of the stone. After 30 minutes after applying the grout, you need to smooth the seams with a special spatula or spatula. When choosing a grout, you should know that the compounds can mimic the color and texture of the present solution. Grout can be of different colors.
Chipping
When the door arch is decorated with a decorative stone, it may be necessary to process the chips. The stone is cut to size, but if its edge remains flat at the junction, then the wall will not look natural. You can make a break, by outlining its shape with a knife. At the next stage, the extra part is bitten off with pliers. On the edge of the mark bite products do not need to start with a small piece, otherwise the product may break where it is necessary. To correct errors you can file, with its help you will give a cleavage smoothness. In addition, the surface is treated with a sandpaper. However, sometimes the chips do not smooth out.
Final decoration
Decorating the interior arch with a decorative stone can be completed by applying a varnish or a coloring mixture. The latter allows you to hide the defects and cracks that formed during the work. To apply the composition, it is better to use an airbrush, but some masters do away with paint brushes. The airbrush allows the application of the mixture from a long distance, the tool must be kept at an angle to the painted surface. You should not cover the entire area completely, it will be sufficient to justify the main protrusions and depressions, this will help get a deep texture.
An interesting effect can be achieved if bronze or gold coloring pigments are used as the basis for the mixture. In this case, only the ends of the tiles need to be toned. Metal with this method of decoration does not strike the eye, but with a certain illumination of the ends, the masonry begins to play with gold reflections.
Conclusion
The arch is a rather small element of the interior, but its decoration sometimes takes a few days. However, you should find time and energy for this work, because the decoration of this part of the room will brighten the house, making it cozy, and the interior - more refined.
Similar articles
Trending Now