Cuff for washing machine: how to change

Although the washing machine belongs to the category of technology, which serves for a long time, yet with time and it can fail. Quite a common problem is the damage to the rubber cuff of the hatch. As a rule, repair or replacement of this component can be done independently, without calling a specialist at home. In this article, we will figure out what role the cuff for the washing machine plays, what are the most common reasons for its malfunction, and how to independently replace it.

Value of this part and fault diagnosis

The cuff for the washing machine plays the role of a limiter that prevents water from getting inside the machine mechanism, and also seeping through the door. If the device is operating correctly, then when performing the necessary operations, all the water is in the tank. In the event of a breach of the tightness with the door closed, the door needs repair.

Causes of damage to the cuff

There are a few common reasons that can lead to the need to replace this component or repair it:

1. Long-term use of the device leads to a natural wear. Like any other part, during operation, the rubber cuff comes into disrepair and needs replacement.
2. Exposure to chemicals that are contained in laundry detergents.
3. Deterioration due to friction with the body. Especially when working at high speed. Specialists note that for this reason, quite often a new cuff for LG WD washing machine is required.
4. Damage by sharp objects during washing. For example, locks, zippers, decorative elements of clothing.
5. The development of fungi and mold due to constant moisture.

How can I remove the cuff

It is worth noting that in modern models of washing machines, it is often possible to remove the cuff without removing the outer casing, this largely simplifies the repair. Owners of old models will have to dismantle the front of the case. In order to remove the cuff, no special knowledge is required. The main thing is that the new rubber gasket should fully correspond to the size and structure of the old one. In order not to make a mistake with the choice, spare parts for washing machines must be purchased in strict accordance with the model of the device or should be sent to the store, taking with it a part, the replacement of which is made.

Visually, you can see that the front part of the rubber gasket is hidden in a special recess. To remove it, first remove the clamps from it. That the cuff of the hatch of the washing machine did not drop out, on it a special collar is put on. It is with him and it is worth starting.

As a rule, it is made of plastic, but can also be found in metallic form. To remove the yoke, you need to take hold of the latch and pull on yourself. If the clamp is made of metal wire, it is best to take a sharp object so that it can be easily pushed. Next, you need to find a mark on the cuff, which will serve as a guide for how to install the element for replacement. Otherwise, leakage can not be avoided.

Installing a new sample

Preliminary it is necessary to clean the entire surface where the work will be done. A new cuff for the washing machine should be installed on a clean and dry place so that it can fit tightly to the structure. The new rubber gasket is tightly fixed over the entire surface of the tank. It must be remembered that the mark on the cuff, which was mentioned earlier, should be at the top. In addition, there are other marks that must also coincide with the tank. Now you need to carefully place the seal in the recess, which is located on the body. During installation, there are often problems with pulling around the perimeter of the circular opening of the tank. Especially often this happens half way, when an unidentified part begins to bounce or crumble. In this case, it is worth trying to fix the cuff simultaneously from the two edges.

After the cuff for the washing machine is installed, it is necessary to tighten it with a clamp. In the event that there is a screw-regulator on the holding device, it will be enough to simply tighten it. It is worth noting that it will be easier to carry out the installation with a metal collar, but the material from which it is made is subject to corrosion. Therefore, durable in this regard will be a plastic holding device.

Verification of work performed

When spare parts for washing machines are replaced and installed, it is mandatory to test the result of the work done. To do this, run the rinsing mode without laundry and see if there are leaks. After a few minutes, you can tilt the machine and check if water is dripping to the floor. If everything is in order, then the tightness of the machine is not broken and you can safely use it. Advice to the housewives on the note: after each wash, wipe the cuff from the inside with a dry cloth. This will avoid the formation of mold and multiplication of fungi, therefore, extend the life of the rubber gasket.