Chainsaw "Calm 180": faults and repairs, operating instructions

Chainsaw "The Stil MS 180" belongs to the class of portable devices. In this case, the engine has a 1400W model. The volume of the motor is 31 cubic meters. See. At idle, the saw is capable of making more than 2 thousand turns. The chain has a length of exactly 350 mm. There is an anti-vibration system.

In general, the saw has proven itself in the market, but it still brings some trouble to the owners. In such cases, the user must be able to independently inspect the device and take corrective measures. However, you should first consider the most common causes of breakdowns.

Instructions for using the tool

Operation of the chainsaw "Calm 180" is carried out according to certain rules. In this case, follow the instructions. Firstly, check the chain tension before turning on the tool. It is always important to keep your hand on the handle. The oil tank cap must be tightly tightened. The oil pump is checked separately. The start button should be switched on after the instrument is securely fixed in the hands. When working with wood, it is prohibited to place the saw at a large angle. It should also be observed during the operation of the tool behind the state of the tire.

Adjusting the carburetor

Carburetor for this model is installed near the starter. Adjust the chainsaw with a screwdriver. In this case, the cover of the device is removed. Further it is important to twist the clutch. After that you can see the carburetor. The chainsaw is adjusted clockwise. In this case, it is important not to twist the spring that is inside the carburetor. If you do not screw the adjusting cam with a screwdriver, then from the first time the saw will not start uniquely.

Starter problems

If you do not start a chainsaw "Calm 180", malfunctions and repair of the starter should be disassembled in detail. Some believe that the problem may be due to improper operation of the tool. In order to inspect the starter, you must first remove the cover, which protects the carburetor. It is not necessary to touch the bus directly in this case. Behind the clutch drum there will be a special screen. You can twist it with a screwdriver. The clutch tape is fixed to the model on the nut.

After disconnecting the drum, it will be possible to inspect the starter. It is located in the presented structure under the carburetor. In order to twist it, you need a key. For the purpose of repairing the part, first of all, the insulation system, which is located in the upper part, is inspected. If the lead wire is moving away from the starter, you will need to use a blowtorch. The problem may also be oil leakage. In this situation, the starter should be simply wiped with a cloth.

The flywheel does not work

If the starter is OK, but the chainsaw "Calm 180" is not being started, the faults and the repair of the flywheel must be disassembled very carefully. This problem is solved quite simply. In order to start inspecting the instrument, it is necessary to drain the gasoline from the tank in advance. There is a flywheel in the device above the air filter. In order to get to it, you have to disconnect the back cover. After that, the cylinder is removed directly.

The next step is to take up the plunger. You can not remove it with a key. In this case, you have to knock it down neatly with a hammer. However, it is important not to damage the carburettor blades. The flywheel in this saw is attached to the small cap. Twist it anticlockwise. After that, the flywheel can be removed. If it has shallow scratches, then it should be simply lubricated with engine oil. If the part is deformed quite strongly, it will have to be replaced, and a new flywheel at "Calm 180" (market price) is in the range of 450 rubles.

Drum Repair

If the flywheel with the starter is OK, but the chainsaw "Calm 180" is not being started, the malfunction and repair of the drum must be disassembled in detail. The main reason for the breakdown is the departure of the cam. It is located near the guide, which is located in the carburetor. For faults of this type, the plungers may also be damaged. To repair the drum yourself, first disconnect the tire. Further it is important to unscrew the protective cover and inspect the carburettor. If no obvious external damage is observed, remove the guide.

Next you need to inspect the cam. It is connected directly to the adjustment shaft. If small cracks can be seen on it, it means you just need to lubricate it with engine oil. After this carburetor should be put in place and try to start the tool. The loud sound of the saw indicates that the cam beats against the wall of the guide. In this situation, you should immediately turn off the device. Otherwise, the adjusting shaft can also be damaged. To independently change the cam, you need to remove the limiter, which is located near the carburetor. After this, it will be possible to completely twist the part. In this case, the adjusting shaft can not be touched.

The cam in the presented saw is installed with a diameter of 1.3 cm. During the replacement of the part it must be carefully tucked into its original place. For this, it is best to use a hammer. However, in this situation it is important not to overdo it and follow the guide. There is a new cam on "Calm 180" (market price) 200 rubles.

Replacement of the connecting rod mechanism

If the starter with the drum is OK, but the chainsaw "Calm 180" is not being started, the malfunctioning and repair of the crank mechanism should be disassembled very carefully. It is quite difficult to solve the problem independently, but if you follow the instructions, you can do a lot. Directly inspect the crank mechanism user is able to remove the back cover of the saw. First of all, you need to disconnect the protective screen. Next, you should start the starter, which is attached to the carburetor.

After it is disconnected, you can see the connecting rod mechanism under the gearbox. First of all, it is important to inspect its plates, which are located in the upper part. Sometimes, due to overheating, they can deform. In this situation, the part will have to be completely changed. Spare parts for chainsaws are better to buy in specialized workshops. In order to extract the connecting rod mechanism, it is necessary to use a wrench. In this case, it is more expedient to ask for help from a friend, since it is quite difficult to solve this task independently while holding the reducer cover.

Problems with the circuit

The chain for the chainsaw "Calm 180" is installed in 3/8 "increments. It is fixed to a special tire, and a spacer is used to stretch it. At the bottom of the structure there is a circuit catcher. To replace it, The new chain for the chainsaw "Calm 180" can only be purchased at specialized workshops. After removing the retainer, it remains to disconnect the trap directly. v chain. install it should be by the sprocket.

Throttle Repair

If the chain saw does not start, the problem may be in the throttle. In this situation, it's difficult to cope on your own. This is due to the fact that it is difficult for one person to adjust the throttle tension. In order to inspect it, the user must get to the fuel system of the saw. In this case, the side cover is removed. After that, the connecting rod and the bore are inspected. If the check valve is dirty, the choke may have broken. In this situation it is necessary to replace it. Spare parts for chainsaws are better to buy in specialized workshops. In order to replace the part, it is recommended first to remove the tire. After this, it is important to tackle the clamp on which the throttle is held.

In the presented model it is fixed on the body with two bolts. With a nut wrench, you can easily unscrew them. The next step is to remove the choke from the upper side. To do this, you will also need to use the key. Stretching it, in the long run, should be good. This will require the help of another person. However, one end of the throttle can be fixed independently. If the valve as a result does not fit snugly against the cover, then the throttle is not tight enough, and it should be removed again.

Replacing the gearbox

If the chain saw does not start, the problem may be with the gearbox. There are breakages of this type, often due to the wear of the protective gasket. In this situation it is important to inspect not only the gearbox, but also the fuel system. Often it becomes a cause of breakdown. If the pump leaks, it means that gasoline can get on the reducer. In this situation, remove the protective cover and disconnect the carburettor. The next step is to remove the reducer directly.

The fuel pump is located above it. If a leak is not detected, then you need to pay attention to the lower part of the reducer. When its hole is clogged, it should be cleaned. To do this, you need to use a cloth. Sometimes the central channel is damaged due to some foreign object, and the part has to be completely changed. However, such cases are extremely rare.