Wagner ("Wagner") - spray gun electrical (Germany): user's manual

Technologies of air dispersion have been used by companies targeting the residential segment for several years. If earlier such equipment was considered difficult for home use, now the tool manufacturers actively introduce their fans to products of this kind. A special place in this segment is occupied by the company "Wagner". The spray gun of this company is presented in different versions, but the special interest from the consumer is caused by apparatuses with electric drive.

Assembly instruction

The pistol consists of a whole group of components that can be disassembled. The main elements include the union nut, the pneumatic cylinder, the volume regulator, the suction pipe, the membrane, etc. First of all, the Wagner spray gun is equipped with a one-piece diaphragm so that its cotter points upward. Then the valve cover is installed, after which it must be tightened securely. The ventilation hose is attached to the lid itself and is also tightly fixed.

After this, it is necessary to advance the oil seal in such a way that its slot is projected into the nozzle, forward. Then the nozzle is put on the body of the device by twisting. Using the union nut, it is necessary to install the air cylinder cover onto the nozzle of the Wagner gun. The spray gun is also equipped with a packing gland with the working material to which the suction tube is supplied.

Turning the gun on

Before starting the device, make sure that it is connected to the network with sufficient voltage. Also before switching on, you must disconnect the container and align the suction tube. Paint material is poured into the container placed on a flat surface, after which the device is screwed to the gun. Directly start the mechanism provided that the device has a stable position. It is necessary to pull the fuse of the fuse, which is included in the system of the trigger device "Wagner". The spray gun of this brand in some versions is provided with a two-stage bracket, so the launch is realized in two stages. First, the turbine is activated, and then the material is ejected. Spray intensity depends on the force of pressing, which can also be adjusted to the needs of a specific task.

Spray technique

The quality of the result after applying the paint by any spray gun depends on how clean and smooth the work surface was. Therefore, every effort should be made to prepare the target site. It is important to take care of the surrounding area, if it is not to be treated. Such places must be covered with film material. Before starting work, you should test the machine by performing several spraying operations on a piece of cardboard, newspaper or other unnecessary material. It is important to keep distance in the process of work. The distance of the order of 10-15 cm from the working surface is optimal for household pistols of the "Wagner" brand. The spray gun is moved by slow and smooth movements, which will make it possible to achieve a uniform laying of the material. If in the process of work on the nozzle the paint-and-lacquer flow began to form, it is necessary to take a break and perform the cleaning of this zone.

Ending the work session

After painting is complete, disconnect the gun from the mains and remove the container. If the repetition of working arrangements is not expected in the near future, then the capacity must be purged. This is done by quickly opening and closing the lid or by discharging the consumable material to the original paint storage site. Next, he disassembles the Wagner spray gun itself, so that it can clean its individual components. The rear and front parts of the device must be turned so that they are facing each other. Then all the contaminated areas are washed with a special mixture for removing the paint.

Particular attention is paid to the further processing of the container. Clean it with a solvent with water. It should be filled with its active cleaning medium and used as a working material. This operation must be repeated until the paint spray gun gets rid of the traces of paint in the part of the spraying infrastructure. Evidence that the inner surfaces of the gun are clean will be the release of clear water from the nozzles with a solvent. Then the device is again disposed of the auxiliary functional parts and left for storage in a dry room with room temperature.

Safety measures when working with the device

To prevent the risk of ignition of consumables, the manufacturer recommends the use of varnishes, paints, enamels and polishes, in which the fire point is at least 21 ° C. Also it is not recommended to use a spray gun in rooms where there is an open fire, sparks, smoldering wires and other sources of ignition.

Operation with the spray gun will be safe for the operator only when using personal protective equipment. In the basic set of a pistol such accessories are not provided, therefore it is necessary to take care of it initially. Glasses, gloves and apron are the minimum set of overalls recommended for workers who use Wagner spray guns. Reviews are also advised to use respiratory devices, as long-term spraying fills the room with a fog that is hazardous to the respiratory system from fine paint particles.

Conclusion

Wagner offers a range of suitable sprayers that are suitable for domestic and professional tasks. In the domestic market, the devices of this company are relatively inexpensive. For example, the model Wagner Wall Perfect with a capacity of 230 ml / min. Can be purchased for 6-7 thousand rubles. According to the calculations of specialists, this potential is enough to serve a strip of 15 m in 10 minutes. What is even more important: almost all models of this manufacturer support the possibility of spraying heavy viscous mixtures.