The Hendershot generator. Hendershot generator circuit

The creation of an energy generator, which works completely autonomously, has long been stirring the minds of mankind. It is difficult to boast of special achievements here, although, if we recall Chizhevsky's chandelier, this direction does not look hopeless at all. In the framework of this article, we will talk about the fuelless generator of Hendershot. The scheme of this device (probable) will allow all those wishing to verify the truth of the information.

View History

The inventor of the device under consideration is the American physicist Leicester Hendershot. For the first time, his generator was introduced to the general public in 1981 in Toronto, where at that time a congress was held on the energy of the gravitational field. Then it was reported that it works because of the presence of a magnetic field near the Earth. From this it emerges that an important role is played by its location, as well as its orientation toward the southern and northern poles.

The inventor himself, Lestor Hendershot, did not live up to the congress. He died in 1961 (officially - committed suicide).

General information on the creation and related processes

The first mention of this device refers to the range of 1927-1930. According to the available records, Hendershot received a usable device with a power of 200-300 watts. Then, for a short time, Lester is honored by the American press as a national hero. But soon praise in his direction is replaced by accusations of charlatanry and fraud.

At the same time, the inventor himself is injured by electric current and no longer comes forward with his developments. According to his son, Mark Hendershot, his father received $ 25,000 for not disclosing information about the generator.

That's all. And let's go directly to the device. You are interested in the generator of Hendershot? Scheme of component disconnection? But before dealing with such issues, let's find out what is needed directly for the device itself.

Necessary materials

So, you need the following components:

1. The copper enameled wire coil is 0.95 millimeters in diameter and 50 meters in length.
2. Two pieces of copper insulated PVC wire, diameter - 1.5 millimeters, length - 18 meters. For convenience of the subsequent work it is possible to use wires with isolation of different colors.
3. Two unpolarized capacitors. Each of them should have a capacity of 500 microfarads.
4. 150 wooden rods, the diameter of which is 3 millimeters.
5. Four unpolarized capacitors. The capacity of each of them should be 1000 microfarads.
6. Two transformers with a ratio of 1: 5, designed to work with a voltage of 110-220 volts.
7. One panel made of wood, plywood or chipboard, with sides 100/60 centimeters.
8. Copper wire with PVC insulation, whose length is 10 meters, diameter is 1 millimeter.
9. One rectangular steel rod, with parameters of 10 / 0.5 / 2 centimeters.
10. External socket, rated for 110-220 volts.
11. A sheet of cardboard, wood, plexiglas (but not metal) with sides 10 by 10 centimeters.
12. Two guide rails, which are used in furniture fittings (but without wheels).
13. Magnetic bar of rectangular or cylindrical shape. The diameter is 1.5 centimeters, the length is 10 centimeters.
14. Two cylindrical steel bars. The length is 8 centimeters, the diameter is 2 centimeters.

Required Tools

Some materials are few. To simplify the production process, the following tools are needed:

• Ruler (length of 30 centimeters should be more than enough);
• A pair of pliers;
• Indelible marker;
• pencil;
• Flat and curly screwdrivers;
• Insulating tape;
• drill;
• A 3 mm drill bit;
• epoxy adhesive;
• Adhesive double-sided adhesive tape;
• Ten self-tapping screws, the length of which is 2 centimeters;
• Soldering gun;
• Twelve screws, the length of which is 2 centimeters. Will be used for fixing capacitors;
• wrench;
• solder;
• flux;
• stationery knife.

To summarize, it's difficult not to mention the simplicity of the set. Due to this, it can be concluded that the assembly of the device is relatively easy. Before you start creating this device, we suggest you familiarize yourself with its advantages and disadvantages. Also, your attention is represented by two schematic images on which the work will be carried out.

Benefits

So, as its strengths lead such arguments:

1. Does not need fuel.
2. The habitat is not polluted.
3. Does not create noise.
4. Has a significant economic effect.
5. Can work for years without maintenance.

disadvantages

This generator has certain drawbacks. In their quality, these features are distinguished:

1. Lack of complete knowledge of its mechanism.
2. The need for experience in creating rather complex schemes.

Schematic images

There are two main images that claim to be true. It should be noted their similarity. Therefore, if you wish, you can personally check the generator of Hendershot. Scheme, does it work or is this another myth?

In the original version there was a pair of coils in which the capacitors were located. Transformers were used from radios. The coils were tuned for mutual resonance. This model worked only when it was oriented to the south from the north. According to Hendershot himself, the amount of energy was enough to ensure the operation of a small engine, which was confirmed by the experiment with a toy airplane.

Getting Started

We begin to produce the generator Hendershot. The scheme itself can be implemented without problems, but for this it is necessary to follow the instructions. First, take the panel. Draw on it two circles, the diameter of which will be 100 millimeters. The distance between their centers should be 50 centimeters. In case you do not understand how and what to implement, look at the diagram. In its upper right corner, these parameters are indicated.

On the circles, we mark the points at regular intervals. Then they need to drill a 3 mm drill bit. Insert in them wooden rods. They should rise by 70 millimeters. If this parameter is exceeded, it must be trimmed. Then gently straighten the wooden sticks after pruning.

Take the wire, the cross section of which is 1.5 millimeters by 2, and start laying it between them. It is necessary to make 12 turns per coil. Then we take the wire 2.5 millimeters to 2. It is already necessary to lay also 12 turns for each coil.

We have two types with different color designations. Each type of wire must be wound 6 times. Remember that the coils should have the same number of turns. Also, do not forget to leave 50-60 millimeters above, so you can connect to them. During assembly, it is advisable to lightly press the windings with a wooden ruler so that they lie down properly.

We make coils for controlling the magnetic resonator

For this, it is necessary to wrap two cylindrical bars with a layer of wax paper. It is then superimposed with 40 turns of wire, the cross section of which is 1.5 millimeters. Using furniture fittings, plastic or cardboard, we produce a movable mechanism. We fix on it with the help of epoxy glue two previously manufactured coils. But they must move without significant effort and distortion. The length of the guide elements should not exceed 250 millimeters.

We place capacitors

Now we need devices for 500 microfarads. On their bottom we glue a double-sided adhesive tape. It is necessary to place the capacitors in the center of the made coils. After the devices are placed at 500 uF, the same should be done with devices per 1000 microfarads. Two capacitors are placed on the panel on the outside of the coils. The devices are non-electrolytic, so they have a considerable size. Therefore, it is not superfluous to think about their compact placement. We fix the remaining constituent parts of the circuit. Transformers must be mounted on the panel.

Installation of the structure

So we come to the end of the creation, and soon it will be possible to check the generator of Hendershot. Free energy, instruction by yourself, the scheme - you can get everything and do it, giving several hours to the production process. Connect all the elements thanks to soldering. Also pay special attention to the accuracy of the assembly. Try to stick to this scheme as much as possible.

Also, be careful not to confuse the end and the beginning of the winding during the connection of the coils and capacitors. Also check the mounting strength. Then you can already connect the outlet. To do this, it must be installed on the panel in a convenient place for you. All open wires must be wrapped around with an insulating tape. For this purpose, a heat shrink tube can be used . In this case, security must be put on the first place, because the price for its violation is your health and even life. So do not feel sorry for the insulating material.

We regulate

The device itself has already been assembled. We will work with the block of the magnetic resonator. As a load, you can choose a lamp. We connect it to the device and start moving the coils to the magnet to get maximum efficiency. You can judge this by the strength of the lamp's glow. Once the maximum effect is obtained, stop the adjustment. During this process, do not touch the iron bars on which the coils are wound. If you need to work with them, use a dielectric material.

Reviews

If everything was correctly done, then you can observe a very good level of power. So, some craftsmen even boast designs for 4-5 kilowatts. This is more than enough to ensure the operation of a rather large amount of equipment. Although it should be noted that the design in such cases is seriously improved. And what do they say about such a generator Hendershot considered? Scheme, reviews of it deserve attention. It is suitable for those who begin to practice in practice fuel free energy sources. Not in the least such comments can be heard thanks to the relative simplicity of the design and the process of its assembly.

Conclusion

So we figured out how to make the Hendershot generator . The scheme presented here can be improved to obtain more power, which is proved by the reviews. But at work it is necessary to be careful. If you decide to improve, carefully understand all the physical processes that you will be dealing with in order to avoid negative consequences.