How to make a Tesla generator

The well-known scientist N. Tesla created a generator that operates without fuel, while generating electricity. The inventor's goal was to create such an engine or mechanism that would not move in space, but was able, like a living organism, to extract energy from the environment. Modern craftsmen have not lost interest in the invention of Nikola Tesla and even try to implement it. If you are interested in the question of how to make a generator, the proposed material will help in this.

The generator, invented by N. Tesla, produces an alternating current. He thought about its creation even during his studies at the school in Graz. He found a solution to this problem while walking around the park and immediately began to draw schemes of the future generator on the sand. In his scheme there were two electric circuits that created a double stream of charged electrons, which the motion was given by induction.

How to make a generator Tesla, can tell both in the school lesson, and in the circle of technical creativity. But in practice it is difficult to implement the creation of the device, since the use of an induction coil can be dangerous, and the equipment is too difficult to transport. And yet there is a generator design that is free from the listed drawbacks. It is portable, has a large capacity, operates from a network of 220 or 120 volts, and is easy to operate.

Before making the current generator, you need to make a frame, which is necessary for winding the secondary circuit of the coil. The frame is a cylinder, the length and diameter of which are 700 and 80 mm, respectively. To create a frame, you need cardboard or thick paper. They are glued to a metal or wooden frame. For this purpose, a piece of water pipe is suitable. Liquid, hot joiner glue should be applied on paper or cardboard and tightly screwed onto the frame, with the thickness of the walls should be from six to eight mm. Then the resulting frame should be wrapped with string, and the turns must lie close to one another. After drying, the frame is removed from the frame and then impregnated with hot paraffin. So how to make a generator Should be very high quality, you should pay attention to the thoroughness of coating, this affects the work of the entire installation.

In order to fix the wires, two holes must be drilled in the frame, and they should be from the upper edge at a distance of 100 mm. After this, the coil of the secondary circuit must be wound around the whole length of the frame, for which a wire of 0.2 to 0.3 mm is needed. The second end of the winding is fixed in two holes at the bottom of the coil, which are drilled the same way as the upper holes. For covering the winding of the frame, it is better to use a high-quality insulating varnish. Then from the plywood, pre-impregnated with paraffin, you need to cut a circle with a diameter that allows it to fit tightly on the frame from above, like a cork. At its center, using a brass bolt and nut, strengthen the porcelain insulator. In order to know how to make a generator correctly, you must adhere to certain requirements. So, the insulator should be not less than 100 mm. The upper end of the bolt of brass, with a thread, should protrude above the insulator.

The generator should have two oscillatory circuits, which are wound with a copper wire, the diameter of which should be from two to three millimeters. Winding should be done on a ribbed frame, which has from 4 to 6 racks of any insulating material. The racks are reinforced at the top of the drawer - the grounds for the entire installation. Between coils there should be a distance equal to 20 mm, and between the frame of the secondary circuit and the oscillating circuits - 15 mm.

The resistance in the chain of grids should be three tons each. The resistance of the generator tubes is wire and is between 50 and 100 ohms. The device uses a mica, variable capacitor, with a large distance between the plates, a half-wave rectifier for powering the generator and a power transformer. Initially, the lamps are switched on, then high voltage. When approaching the coil of a fluorescent lamp at a distance of 300-400 mm, it begins to glow.

Now, having become acquainted with how to make the generator yourself , you can cope with the task yourself.