How to set a monument yourself - granite or marble

When people close to us leave our lives, we try to do everything possible to honor the memory of the deceased in the best way possible. Most often, we express our feelings of loss on the monument, which is customary to be installed on the site of a person's burial. All of them differ in the material and its quality, color and texture, shape and height. But in most cases the life of any monument directly depends on its correct installation. Most often people resort to the help of specialists in this field, but with the necessary tools, you can do all the work yourself. Consider how to install the monument yourself, so that it lasts a long time.

Requirements for work execution

Many people know that installation works of this kind are best performed in the warm season. But not everyone knows how to properly install the monument on the grave, and That a significant role here is played not only by weather conditions, but also by the state of the earth cover. On the nature of the soil at the time of the work will depend on the reliability of the installation of the monument and its durability. Therefore, if you are studying the question of how to install a monument yourself, it is important how to study the factors that influence the success of the whole case. The frozen ground is not the best foundation for the foundation, and for the drying of building materials, warm weather will be most favorable. Choosing the right time, you can safely collect everything you need.

Required inventory and materials

How to install the monument yourself? Find all the tools to do the work is not so difficult. Practically every owner will have a shovel, a trowel, a scrap, a spatula, a rubber kink or a heavy hammer, several jumpers, a tape measure and a special level for construction. If one or two tools are missing, they can be replaced with similar tools. The list of building materials for installation of the monument includes several sandbags, crushed stone, a bag of cement and water. The standard weight of ready-made monuments is usually 100-120 kg, so several people will be needed for productive work.

We make the preparation of the basis for the monument

First of all, on the site of installation of the product it is necessary to dig a shallow hole, the width of which should be almost one meter. On top of it are placed one and a half meter jumper (they can be replaced by ordinary channels, parts of the old fence, poles). Such a frame will allow to establish the monument in the cemetery reliably and for a long time, without letting it prematurely fall due to the sagged soil.

The installation of the jumpers should be accompanied by monitoring the level - even from the slightest error in the measurements, the monument may eventually tilt or fall. Only a perfectly flat base ensures reliable fastening of the stone product. Find the corners of the grave can be with the help of scrap, after which they are marked to mark the parameters of the foundation. The top of the earth embankment is safely removed, after which the general level of the foundations of other monuments is determined.

Mounting the stand under the stela

Since we are interested in how to establish a monument on its own, that is, without the help of specialists, then we prepare the solution ourselves. It should have a liquid consistency, contain a minimum amount of water, cement, as well as sand. The resulting mass becomes a springboard for the stand under the monument - it is leveled and adjusted to the intended height. Only the surface of the slab is made smooth, the corners do not require such thoroughness. After that place the flower beds, venturing into the ground for 25-30 cm. All works are accompanied by an indispensable leveling with the help of a level. The drying speed of the solution can be increased by sprinkling the substrate with cement. Then proceed to the direct installation of the monument.

How to install a granite monument yourself

The peculiarity of such material as granite, in its immunity to water. Excessive liquid will not help to fix the product. The material is very susceptible to mechanical shocks, so work with it should be extremely accurate. On the prepared basis, install the stele, fixing it in place with a metal pin. It is placed inside a special hole inside the stand, and the other end is attached directly to the arch. Further fixing takes place with the help of a solution - it is used in the joints of stelae and supports. The drying time of concrete can fluctuate depending on climatic characteristics, wind speed and season.

How to install a monument of marble yourself

The process of installing the marble stela is practically the same as for the installation of a granite monument. Marble, too, is not very strong material, and therefore work with it should be done very carefully. The monument is also installed over the pin, and the joints are lubricated with super-resistant glue. This will protect it from the effects of low temperature and prolong its service life.

The finished structure can be very shaky at first. It is very important to protect the stele from pressures and external influences - it should remain in a stationary position until the solution finally solidifies. Seams and joints are wiped with a cement paste moistened with water. After drying, they should be sanded and remove excess.

Final works

After all the main process of installing the stelae is completed, it is necessary to wait 10 to 14 days until the solution dries up completely wherever it was applied. After this period, the place for the flower bed can be covered with earth - it is better to bring a quality soil with you to create good conditions for vegetation. Instead of land, sand or marble chips are often used, which gives the monument an unusual appearance and does not look so dull in the cold season. The territory inside and around the monument is often planted with flowers and bushes, laying paving slabs in the passages.