How to outweigh the door of the refrigerator "Indesit": a step-by-step instruction

The refrigerator is an important appliance in every home. Sometimes it is required to outweigh the door on it to provide a convenient opening. Often this is necessary because of the interior features. How to outweigh the doors of the refrigerator "Indesit"? The procedure involves several operations, but first you need to prepare everything you need to work.

Reasons for reinstalling the door

Before you get acquainted with how to outweigh the door of the refrigerator "Indesit", you need to find out why they do it. Work is required in the following cases:

• Inconvenient use of the door;
• Nearby there is some device that does not meet the requirements of operation;
• A personal desire to do something new in his kitchen, which will bring originality to the interior.

Familiarity with the instruction

Before work, it is necessary to familiarize yourself with the instructions that are included in the equipment. There is usually a description of the stages, how to outweigh the door of the refrigerator "Indesit". When you buy the door are on the right side, and therefore are presented tips for hanging to the left.

You should inspect the device, find stubs, swivel hinges. The body must have special fasteners. It is necessary to start work only after the principle of work becomes clear.

What is needed?

Weigh the door of the refrigerator "Indesit" with:

• Flat and cross-type screwdriver;
• Spanner wrenches.

Removing the door

It is necessary to remove food from the camera, turn off the device, and let it go. This is required to straighten the rubber sealant so that it will regain its normal shape, which is necessary to adjust the door in a new position. In "Indesite" fastening is provided by a turning loop with some variations in the location of the hardware.

How to outweigh the door of the refrigerator "Indesit", so as not to damage the equipment? Use a screwdriver to eliminate it. Removal of decorative plugs is done with a knife or with a flat screwdriver. Bolt caps should have holes for a Phillips screwdriver. If they are not available, select the wrench with the required parameters.

First you need to take a false panel to have access to the wiring harnesses, which serve as a connection between the door display and the automation. It is necessary to loosen the harness so as not to damage the wires with the door removed. It is important to disconnect the display panel.

Then the handle is removed and the lower fastening of the door is loosened, and then the upper one is loosened. It is necessary to detach the lower canopy and release the lower loop. To remove the upper canopy, you must lift it up. The product must be placed in a safe place, after which it is necessary to choose the site of fastening the loops on the other side. The holes are closed with decorative caps or plates. Often, special details are required, it all depends on which refrigerator Indesit. The doors must be re-door based on instructions.

Installing the door on the opposite side

It is necessary to install the hinges before outweighing the door of the refrigerator "Indesit". The instruction includes the necessary rules for the performance of quality work. First, plugs are removed, and awnings are attached to the holes. Do not immediately tighten the bolts firmly, because you may need to adjust the position of the structure.

If there is a closing sensor, during operation it also needs to be weighed, and for this it is necessary to take care of attaching the fasteners. When it is located in the center, a permutation is not required. The sensor may not be, because in some devices it is located inside the unit, under the skin. This applies to the switch of the light bulb: it is often fastened inside, because of which a permutation is not required.

The samples should have guide pins, so installing them in a new location will be very easy. But it also happens in another way - the pins are located on the door, which determines the sequence of actions. Canopies can be adjusted and height. First you need to install the bottom hole, and then the top one. They are bolted.

The door should be adjusted by checking the quality of the seal. How to outweigh the doors of the refrigerator "Indesit", so that everything was done firmly? For this level, but you can compare everything visually. It is necessary to measure all the parameters and adjust the deficiencies. When the door is repositioned, the refrigerator should be tilted back slightly. After opening the door, the adjustment will be made faster.

Changing the handle position

When the handle is part of the enclosure, you do not need to reinstall it. But how to outweigh the door of the refrigerator "Indesit", if the handle has 2 parts? To do this, you need to re-attach the harness that is heading toward the display. At the top there should be a hole, which will be considered a blind. It is necessary to disconnect the connector with the wires, stretch the bundle, fix it.

The handle is removed with a screwdriver, and for a new installation, muffled holes are needed. It will only be necessary to remove the handle, the plugs and attach them to a new location. Old areas should be hidden with blanking plugs.

Recommendations for beginners

Instructions for the work will allow you to understand how to outweigh the doors on the refrigerator "Indesit". Tips will help to perform this work qualitatively:

• Many refrigerators "Indesit" are two-chambered, and therefore it is necessary to perform the reinstallation of both valves, otherwise the operation of the equipment will become more complicated;
• First it is better to start the refrigerating department, and then to the freezer;
• If the technology does not have a bottom hole, because of which it is necessary to additionally purchase a left-hand lower loop, you can make holes yourself;
• If there is a display, installing the door becomes more difficult: you will need to remove the cable under the upper loop;
• The procedure will not solve the problem of loose fit of the door, as this indicates the deterioration of the sealant;
• To independently adjust the density of the fitting of the door, the deflection of the refrigerator by the adjusting supports will be required;
• After the repair work should not include equipment for about 8 hours, and then it is ready for operation;
• If the refrigerator is under warranty, then you should not interfere with it yourself: such work can cause a complex breakdown;
• If there is any doubt in the correctness of the work, it is better to contact a professional.

If the old gum is dried, then it must be replaced with a new one, and the problem will be eliminated. And then the overweight of the door is not required. It is enough to follow all rules of the instruction, and the equipment will work very long.