How to nail the lining to the wall with a stapler?

Working with wood requires certain knowledge and skills from builders. A person who does not have sufficient experience and special equipment, it is difficult to mount such a material. But the lining is knocked out of the general mass. It has already been processed properly, so it can be installed even by a non-professional.

There are several methods that allow you to sew the room with a lining. Each of them has its advantages and disadvantages. The implementation of fasteners with a stapler is considered one of the simplest methods. It is easier for a beginner to apply this approach in his work. How to nail the lining staples construction stapler, will help to understand the advice of experienced professionals. Even without special skills in carrying out such installation, the novice master will be able to perform the job well. For this, it is necessary to familiarize yourself with the step-by-step instruction.

The essence of the method

Asking about how to nail the lining to the wall with a stapler, you should familiarize yourself with the recommendations of specialists. This approach uses an identical to a clerical stapler tool. Its building version also has a compartment for staples and a retainer. This is a flat pressure plate.

The staples in this tool are, for obvious reasons, more massive and stiffer. When pressure is applied to them, there is pressure. The bracket leaves its compartment and is fixed in the material. Moreover, the fastening element becomes at an angle of 45 degrees. Then the ends of the bracket are pressed under the influence of the same pressure. The fastening element tightly stops in the material. The fixing nodes are durable. At the same time, the work is done quickly and without much effort. This method is quite popular today. It is not difficult to master it. It is necessary to know a few subtleties.

Features of work

Getting acquainted with the information on how to nail the lining to the wall, ceiling, you need to consider the features of this process. In this case, it is necessary to take into account the features of the room and the type of foundation. Depending on the material of the wall, the type of frame is selected. Without it, the lining can not be installed.

If it is to be mounted on the ceiling, the frame must be reinforced. At its installation also additional materials (glue and кляймеры) are used. The stronger the carrier system is under the lining, the longer the lining will be. The process of creating a frame is given special attention. When choosing materials, the following point is taken into account: will boards and profiles be exposed to temperature fluctuations (for example, in a bath) or high humidity (for example, in a shower room or bathroom)? Even under favorable environmental conditions inside the building, a skeleton is necessary. Otherwise, over time, the lining will loosen.

Preparatory work

Before installing the frame, prepare the base. When deciding how to nail the lining to a brick wall, concrete or other materials, it is necessary to investigate the unevenness of the surface. If they are very large (exceeding 10 cm), it is necessary to fill in the cracks, dents, bulges.

In order to avoid the formation of fungus, other microorganisms and pests, the surface is treated with an antiseptic primer. This is especially important in a sauna or bathroom. After making sure that the foundation meets construction standards and requirements, proceed to the next stage.

Mounting the frame

Studying how to nail the lining to the wall, you need to consider the technique of mounting the frame. First, using the meter and the level on the bottom is the lowest point. It will be initial during the installation process. A horizontal line is drawn from this point along the perimeter.

Next, using a level and a building angle, a vertical straight line is applied. By marking on the basis of mounted metal profiles or wooden slats. In the latter version, the material must be impregnated with a fireproof solution and an antiseptic. The metal frame is more reliable and durable. But its cost is more than a wooden base, and the work is more complicated.

Additional materials

To understand how to nail the lining with a stapler, you should consider each action. After installing the frame, it is necessary to insulate the walls or ceiling. This is especially important for a bath. Heat will not quickly leave the room. For this purpose, mineral wool or other special materials are used. Foam for indoor installation is not used. Also, when installing the lining in a humid room, you will need to lay a layer of waterproofing. To ensure that the structure does not loosen up over time, an OSB sheet is first attached to the frame. It can be only 6 mm thick. This is enough to give the skin rigidity.

Next, you need to prepare the glue. Without it, fastening with a stapler or other mounting elements will be unstable. Even when frozen, the glue is elastic. Therefore, under the influence of temperature and humidity, the lining remains flat.

Wall paneling installation

When studying the question of how to nail the lining, it is necessary to consider the stapler method in detail. To keep the casing firmly, it is better to use "liquid nails". Sheets of lining are fastened so that the bracket can easily fit into the bracket at an angle of 45 degrees. Depending on the thickness of the skin and the frame material, 4-6 staples are required per sheet. They are installed from the bottom of the lining. This makes fasteners invisible. The glue will give the strength of the entire structure. Work with a stapler is quick and easy. This method is applicable even for ceilings.

Sheathing of the ceiling

Modern building materials allow you to fasten the lining with a stapler even on the ceiling. To do this, you need to take into account some of the nuances. Being interested in how to nail the lining to the ceiling, it is necessary to understand that the whole system should hold firmly on the ground. After all, with insufficient strength at one point, it can collapse on the heads of the owners. To prevent this annoying situation, a metal frame is mounted on the ceiling. The OSB sheet should be about 10 mm thick (larger than on walls). This will further strengthen the structure. The use of glue in the process of fastening the lining is mandatory. The work takes longer, but the cladding will hold firmly on the frame.

The final stage

If you independently execute the plating of the premises, you can get some gaps between the boards in the corners. Solving the problem, how to nail the lining to the ceiling in the bath, on the walls, it is necessary to be ready for this situation. This is not a problem.

The gaps between the sheets on the corners must be covered with window beads, slats or special corners. These elements should be glued in, rather than punched. For a ceiling wooden baguettes in tone of vagonki apply. This will hide the unevenness. They are inevitable in any case. Aesthetic effect will be better. The lining will look neat. It is pleasant to the owners and their guests to be in such a room.

After considering the technique how to nail the lining to the wall or ceiling with a stapler, you can do all your work yourself. It is carried out in stages. Taking into account all the features of the process, having got acquainted with the recommendations of experienced specialists, you can decorate the premises qualitatively. In this case, the board will be firmly supported on the base. The life of the coating will be long. Even a novice master will be able to perform all the stages of the work independently.