How to adjust the plastic door? How to adjust the entrance plastic door

Before installing the plastic door, you need not only to choose the manufacturer carefully, but also pay attention to its components. Only in these cases the door will serve you more than a dozen years. But after a while after installation, the door mechanisms may fail. To eliminate this malfunction, you do not need to contact the masters. You can set up the mechanisms yourself. To do this, you need to know how to adjust the input plastic door yourself.

The most common causes of breakdowns

As a rule, all malfunctions of plastic doors arise as a result of a violation of the position of the blade itself. Because of its frequent use, all mobile mechanisms are gradually breaking down. Therefore, before adjusting the plastic door, let's first figure out when to do it.

• The lower part of the door rubs against the threshold. As a rule, this is due to insufficiently tightened mechanisms. This is due not to the quality of the door itself, but to the carelessness of the master who installed it. In addition, the door leaf may sag under its own weight. This is mainly due to the weighted double-glazed units.
• The middle part of the door (near the handle) rubs against the plastic lining. This is usually due to sudden temperature changes.
• The door does not close sealed. The cause of such a malfunction can be not only the same sudden temperature changes, but also the displacement of the pressure roller after a long use of the doors.

Troubleshooting in plastic doors

Many, probably, think that knowing how to adjust the plastic door, it is not necessary to treat it carefully. But, unfortunately, this is not so. The door can be adjusted several times. But after a while there will come a time when this procedure simply does not help. Thus, it should always be remembered that prevention of doors should also be taken seriously, as well as their choice or installation.

So, before you buy this or that model of doors, never refuse to complete it, even if it increases the cost of your purchase. Otherwise, before adjusting the hinges of the plastic doors yourself, you will need to again spend time and money on finding this or that accessory.

Required fixtures for plastic doors

The most important tools for adjusting plastic doors are considered to be the following:

1. Microlift. This device will help to eliminate any malfunction of any size and weight of the doors. It helps to prevent the sagging of even the heaviest door leaves. The microlift takes over part of the door load, but only in its closed position. It can look different. The most common types of it - a roller at the bottom or a movable plate at the top of the canvas.
2. Restrictor of door opening. This mechanism not only helps to prevent the sagging of the door, but also sets the maximum angle of its opening in such a way that it protects the canvas from impacts against slopes.

In addition, before you decide on the choice of a manufacturer of plastic doors, learn more about it. The fact is that many firms neglect the quality of the fittings themselves, they establish a cheaper one, which can also be one of the reasons for the minimal life of the product.

Eliminating slack in the door leaf

We have already found out what the sagging of the canvas depends on, now let's look at how to properly adjust the plastic door with your own hands in this situation.

If you notice that the cloth clings to the threshold, it is necessary to eliminate this malfunction as quickly as possible. To do this, open the doors and find on the top loop a small screw. As a rule, it is a hexagon. In some cases, it may look like an asterisk. In this or that situation, you will need to pick up the key to the screw.

So rotate the screw clockwise. Do two or three turns. Cover the door. Now it should be free to close.

If the canvas sags very much, and these actions did not help to eliminate this malfunction, the specialists give the following recommendation how to adjust the plastic door in height. Locate the adjusting screw under the protective cap of the lower canopy and rotate it a couple of times clockwise. These actions will help you solve the problem with the sagging of the door.

Eliminating the mashing of the door leaf on the side

The mashing of the side door is also easily preventable. How to adjust the plastic door in this case? To do this, find on the lower canopy is now another screw, which is not located from the bottom, but on the side, that is, from the inside of the blade. Again, twisting it clockwise, you can put the door leaf on the right place. It will no longer cling to the jamb and can easily close.

If this method does not help to eliminate the mashing of the door laterally, find the upper canopy, about which was written above, and perform all the same actions.

Adjustment of airtightness of doors

If you notice that your door does not close tightly, then this troubleshooting point is for you. Let's see how to adjust the pressure of the plastic door.

First, take a shot at the ends of the door. There are special eccentrics. Their rotation can be adjusted to the correct mode of the door. The only difficulty here is to find the right eccentrics. Usually at the top, side and bottom of them set to three. All of them should be gradually turned at the same angle in such a way that the door is tightly closed. But since this fitting will only be near the handle, it will still be necessary to adjust the awnings with special screws.

Adjusting the door handle

We have already considered how to adjust the plastic door. But what if its handle does not function properly when opened? Do not worry, you can also remove these hand problems by yourself.

To do this, move the decorative plate 90 degrees. Below it you will find the handle mechanism and fixing screws. Tighten these screws, and the handle on the door leaf will be fixed stronger. Thus, you can adjust its fixation density by yourself, which makes it possible to eliminate the malfunction of the door opening mechanism.

Replacement of handle in plastic doors

Now you know how to adjust the plastic door by yourself. But more difficulties will be caused by the replacement of her pen. After all, such furniture is the most vulnerable. It is also worth noting that the period of its operation is much less than specified by the manufacturer.

The main reason for the breakage of the handle of the plastic doors is the poor quality of the material. Constant use of it foresees cracks, and in the future - to the fact that the handle is completely broken off.

If you are faced with the latest problem, first you need to pick up an analog of your pen. Choose this or that hardware carefully, paying special attention to the identity of the dimensions of the part and fasteners. As a rule, all these devices are almost identical, but it will be superfluous to be reinsured in this case.

The handle is attached directly to the metal screws concealed under the plastic profile base, which are then closed with decorative caps.

We hope our advice helped. Now you know how to adjust the input plastic door yourself.