Than to grease hinges of doors of the car that did not creak?

Perhaps, every experienced car owner wondered what to grease the hinges of car doors, so as not to creak. Indeed, the squeaks and noises in the cabin clearly do not bring pleasure from the ride. Therefore, many drivers produce noise insulation - they seal the doors, floor and ceiling with a vibration plate in two or even three layers. Yes, the effect of this is. But it does not save you from the creaking in the pins. Therefore, today we will analyze what to grease the hinges of car doors (VAZ-2110 including).

Causes

First let's find out where these annoying sounds come from? Squeaks emanate from the friction of the metal, namely loops and pins, which secure the door to the body of the car. It gets various mud, water, dust and other "blizzard" that is on our roads. Over time, the factory grease is washed off, and as a result we hear a characteristic creak and clicks emanating from the car's loops. With a long absence of lubrication, the surface and the inside of the elements are covered with rust. Corrosion processes begin. Of course, the loop of a modern car is too thick to rot, but those inconveniences that will deliver squeaks will simply drive you crazy. Also, the condition of the seals and the adjustment of the locks affect the wear. As shown in the photo, it can be pushed aside with the help of a hexagon: loosen, then tighten.

Over time, if the pins are not replaced or the lock is incorrectly inserted, the door may become loose. Because of this, the metal friction against the metal (namely, the loops) increases substantially. The situation is exacerbated, and the volume of the squeak grows in leaps and bounds. Naturally, car owners are trying to eliminate this problem and panic pours there any lubricant that fell under the arm: old oils, workmanship, and some even vinegar. In most cases this does not help. A qualitative tool should create a thin oily film that will form in the gaps, preventing direct contact between the loops. Pour there is horrible is not recommended.

Than to grease hinges of doors of the car?

"Priora" and other domestic cars have a congenital "disease" - creaking loops. They are the source of an annoying sound that can not be blocked even by loud music. To begin with, you should visually inspect the data of the part. If there is a layer of grease on the hinges, but with particles of dust and dirt, it is recommended to re-process. For this purpose, with the help of white spirit, gasoline or any other solvent, the old factory grease, together with the particles of road dust accumulated on it, is removed from the coating. Then the surface is treated with a consistent composition. Than to grease hinges of doors of the car VAZ-2114? Among the consistently worth mentioning is solidol or lithol. They are thick enough in their structure and do not flow in the heat, like many others. It should be noted that only parts that are rubbing must be treated with lithol. Due to its oily structure, it also repels water well. Thus, moisture never falls into the hinges previously processed by this tool.

Graphite grease

Than to grease hinges of doors of the car? You can do this with graphite grease. This type of lubricant is also universal. Reviews say that it perfectly protects the safety of loops, forming a film between them. By consistency, it is comparable with lithol. Also it is recommended to process graphite grease wheel bolts. With a one-time application, the risk of breaking them is reduced several times.

Than to grease hinges of doors of a car? Machine oil and nigrol

Some craftsmen "syringe" and such a lubricant. Why "syringe"? It is difficult to apply other methods. It is a very liquid composition that literally flows when it hits the hinges. To put a lot of it - means to spoil the door, namely to pollute it together with the rapids to disgrace. The effect of such application is. But do not be zealous: an extra drop of a river will flow down, and you will not be able to remove it from the first time, especially with a wet rag. Due to the water-repellent properties, the nigrol is removed only by a dry rag (anti-corrosion resistance is provided). Before lubricating the hinges of the car doors, be sure to degrease the surface and remove any old deposits from it.

If they are rusty

In the absence of proper care, these elements will quickly rust. They, along with the arches and thresholds are the most vulnerable to corrosion elements. In the neglected case, one application of lubricant will not be enough. And it's not about the number of layers, but about the need to remove old corrosion. After all, the loop will not rust after lubrication, but the composition is not able to corrode those metal particles (shavings) that are inside.

For this, a rust converter is used . Costs it is inexpensive - about 250 rubles per 0.5 liters. This volume is enough for all the hinges, in addition, it will remain for the thresholds. This composition is dipped in a sponge, and then applied to the loop itself. After an hour of processing, the inner and outer part of the hinges will be as new - it is, of course, optional to paint it. But it's time to put the grease.

How to apply?

Thick must be applied with a thin brush or, if it is nigrol, using a pharmacy syringe (can be without a needle). Than to grease hinges of doors of the car? Recently, the compositions in the form of a spray have become very popular. Due to the liquid consistency they are easily applied and penetrate into the rubbing elements. Among such it is worth noting the remedy "Molikot". Judging by the reviews, this substance is suitable for domestic and foreign cars, it is characterized by high water resistance and resistance to temperature changes. Lubricant easily penetrates the gaps and remains there for a long time, creating a small oil film. As a result, the doors easily open and close (the minimum coefficient of friction), and most importantly, do not creak.

Sprays

Than to grease hinges of doors of the car VAZ-2107 or any another? Among the lubricant-sprays it is worth noting the universal funds from "Liquid-Moly" and "VD-40". They are easy to apply and provide protection from friction. You can use them not only on the hinges, but also on the locks (the luggage compartment including). Yes, and generally apply to any rubbing mechanisms. Before lubricating the car door hinges, remember the operating instructions. The main thing - do not apply to rubber products: seals, cushions, belts and so on. The presence of lubricant, on the contrary, will shorten their service life. Rubber will start to crack, stretch and deform.

Rules of application

Note that you do not need to apply a large amount of grease to the hinges. Of course, they will not get any worse from this. It's different. That part of the composition that was superfluous flows down the doors and further into the rapids. As a result, the lower part of the body is covered with a solid oily film. Naturally, it will "magnetize" all road dust on itself. Within a week, the effect of such treatment will become shocking for the car owner - black thresholds and parts of doors with a thick layer of road dust. Normal washing does not eliminate it - you need help rags. And scratching paint on the body, removing all this raid, is a very unpleasant occupation. On the hinges of modern cars there is a special cap that locks into the door pin, it is it to pour grease. The cap will not let it go out (of course, if the amount of lubricant was normal). To evenly distribute the tool over the hinges, it is necessary to open and close the doors several times.

What if there is no result?

There is a situation where when the composition of the door the door continues to make creaks. And not on the closing / opening, but during the ride. Lubricants in the hinges are enough, but the doors still click. What to do? This indicates the sagging mechanisms. If the door is crooked and hard to close, this indicates that there is a generation in the hinges themselves. Most often, car owners solve the problem by installing new pins. But not always it helps: development is not only on them, but also in the hinges themselves. It can be a fraction of a millimeter, but even this is enough for the metal to calmly "walk" inside. To get rid of this, loop loops are cut by a Bulgarian, and then welded. As a result, the gap is reduced - the pin is tighter, there is no play in the door. Previously, all this is treated with a thick grease, most often graphite. After such repairs, the door will be like a new one - it is perfectly closed and does not make annoying sounds.

When to do the treatment?

It is better to do this procedure in the autumn than to lubricate the hinges of the car doors in a severe frost, when the product simply freezes, not reaching the right place. On the eve of the winter season, experts recommend to handle not only the hinges, but also the locks of the doors, as well as the trunk. All the seals and edges (rainwater) of the windows are treated with silicone grease. It prevents the formation of ice. Thus, the door does not freeze after a regular trip to work. Locks are processed directly through the hole for the key - a little poddev it, apply the tool WD-40. After several times, open and close the button of the locking mechanism (thus the lubricant will penetrate the surface of all rubbing elements inside). It is also necessary to process these areas (including door seals) after washing. Especially this applies to operation in the winter. No matter how well you spend with a rag on the body and its elements, there will be some moisture on the elastic bands that will turn into ice in the morning - it will be impossible to get into the salon of such a car. Therefore, it is necessary to handle hinges, locks and door seals, this saves your time for opening considerably and reduces the noise level inside while driving. After all, the creaking of metal is most intrusive, and if you consider that the car rides every day, this greatly affects the psyche and the mood of the driver. After all, you will agree: it's nice to drive in a car that does not have this nasty squeak, but the door opens immediately, and not with a part of the seal.

Conclusion

So, we found out what to grease the hinges of the car doors. For winter it is better to use several means at once: sprays - in the lock and hinges, and silicone - on rubber seals.