If you are a lover of fishing or hunting, then on a long trip you will surely need a stovepole. Such a design can be made independently, using for this purpose hand tools and materials. It acts as an effective replacement for a fire. It will be necessary to spend much less fuel on her work. In his role, dry branches, cones, tree bark, cane or chips may appear. You can use the coals that will remain from the old fire.
Design Features
The stove-powder oven will be much more profitable compared to the standard equipment, which has a grate. Such designs often do not have a bottom, which allows you to place firewood directly on the ground. This slows down the combustion, and if there is a need to lay a new portion, then the combustion will occur almost instantaneously, but the draft in this construction will be maximum. Among the additional advantages can be identified cost-effectiveness, efficiency, universality, as well as autonomy. Among other things, such furnaces have small dimensions, which is very convenient for trips outside the city. Such equipment can burn for a long time without generating an excessive amount of smoke.
Making a stove from a tin can
The stove can be made by primitive technology, for this purpose it is necessary to prepare a tin can, which can be replaced with an iron mug. As a mandatory condition is the minimum size - by the type of high glass. Further, in the bottom of the circle, it will be necessary to make several holes, which will ensure traction. The average ash oven should have holes that must coincide with the internal channel of oxygen movement. You can apply the option, which involves making one large hole, but in this case, the coals will fall out. Now you can fill the jar with small wooden chocks, their thickness should be approximately equal to the thickness of the finger. Such fuel should not extend beyond the edges of the can. It is necessary to lay firewood strictly vertically. After this, it is necessary to remove one choke from the central part, which will ensure the passage of air. In the formed channel it is necessary to place paper, which can be replaced with dry grass, after which it needs to be set on fire. Such a stove-oven, the volume of which is approximately 500 ml, will burn for about 25 minutes, this time will be quite enough to cook food in a hurry. Hunters often make sure that smoke does not occur, and such self-made equipment just excludes the occurrence of smoke.
Recommendations for work
If several people take part in the campaign, then such a bank will not be enough, in this case it is recommended to use a capacity of 1 or 2 liters. However, in this case it will be necessary to maintain a stable combustion with the help of firewood of more impressive sizes, and their number should be larger. If you ignite the flame in such a design, it will burn for about an hour. This will be enough to cook potatoes or fry shish kebab on the coals.
Making a stove from a pan
If you will make a stove-poshehonka yourself, then you can apply technology that involves the formation of a two-layer structure. To do this, use a pan that is made of stainless steel. It can be purchased in a store, but it is quite inexpensive. If you pay attention to the design of this oven, it can be noted that it consists of two pans that have different sizes. These components are built into each other. In the side wall of the pan, which is located outside, it is necessary to cut an opening through which it will be convenient to load fuel. While at the bottom it is necessary to make parallel located grate slots, which can be equipped with turning bridges. These can be ordinary holes. On the grate you need to install a stand, after it is loaded with firewood, on top of all this you need to put a second pan, which has a smaller diameter, it will warm from the flame. The second pan will be covered by fire, among other things, it will additionally be heated from the walls of large capacity, due to this fuel consumption will not be so impressive. The bow for the bowl must be made in such a way that it looks like a removable element. If such a stove-oven is made by one's own hands, then it will be very convenient to use, because it has insignificant weight even in a loaded condition.
Manufacture of a folding furnace
If you are not afraid to spend a little more time, you can work on a folding structure that will be very effective. Working on it, you have to spend more energy, among other things, the master will need to carry out preparatory work.
Required materials and tools
In order to do the manufacture of a folding furnace, you need to prepare a grinder, an electric drill with a set of drills, a tape measure, pliers, files, as well as spokes from a bicycle. Need a piano loops and a steel sheet, the thickness of which should be equal to 1 millimeter. If you can find old sheets from the refrigerator, you can use them. Side walls, borrowed from the old system computer block, will eliminate the use of sheet steel.
Features of work
If a stove-oven is made, drawings should be prepared in advance. Next, all elements of the design should be marked, for this it will be convenient to use templates. Billets are cut out of sheet steel, you can use the Bulgarian for this. In the workpiece, which will form the basis of the bottom, it is necessary to make a hole. After all the edges must be processed by a file, which will eliminate errors. Now it is possible to connect the side walls of the future construction with each other, for this purpose, piano loops on rivets perfectly match. The result should be a box. On the perimeter of the bottom, as well as on the lower edges of the side walls, it is necessary to provide in advance the ears, which must be bent in one direction. Under the box, it is necessary to lay an element that will act as a bottom, with the ears of the two elements connected to each side and forming a tube. It should be installed pins made of spokes, borrowed from the bicycle. Such a small trick will make the construction more stable in the working state. If you need a stove-powder, reviews about which are only positive, you can read all about its manufacture in this article. At the next stage on the grate it is necessary to make additional ledges, which need to be installed in the holes cut at the sides. In the box there must be one more hole through which you can load fuel. Cutouts, which should be done in the upper part of the box, will be able to strengthen the traction, among other things, they can be used to lay the skewers.
Making a stove from several cans
You can choose for yourself the design of the oven that suits you best. For example, a small smallpox can be made immediately from several cans. To begin with, you need to prepare 3 cans, 2 of which will have a smaller size, while another will have a larger one. After this, you need to take care of the presence of scissors for metal, marker, and asbestos. After this, you can proceed with the manufacturing process.
Work on the oven
If you need a small poshekhonka, then you need to start making blanks. To do this, take a large pot, from the bottom of which you need to retreat 20 centimeters. There is attached a smaller bank and a marker. This will create an even circle. A hole is cut through this circle in such a way that the bank enters it, but with some effort. In a smaller bank, you need to make the same hole, and after the smaller can be placed in a larger one. On one side of the jar you need to make cuts of 2-3 cm. Next, you need to use the lid from the large jar, in which a hole is made for the small one. All sections must be sanded. On the wall of the jar you need to make vertical slots, the dimensions of which are approximately equal to 2 cm. The voids between the cans can be filled with asbestos, after closing the lid and fold the metal. Next, you can make a shelf for firewood, for this you should use a piece of tin. This element is fixed after cutting. Such a stove-small oven can have a handle, so that the structure can be easily carried. On this you can assume that the device is ready. It can be covered with paint.
Conclusion
If you need a stove "Poshekhonka", the manufacturer (the company "Mosverf", Rybinsk) offers to buy it at a fairly affordable price - within five to six thousand rubles. However, in this case you will have to spend, and if you do it yourself, you do not need to buy any tools and materials. If you plan to use this design for a long time, it is necessary to provide in advance its design features and size. Only in this way will the equipment be efficient and durable. In general, you yourself can develop your own algorithm of work. Dimensions can be chosen empirically. This is advisable for the reason that you will not have the opportunity to spoil the materials and spend unnecessarily, because you will not need to acquire anything, and you can get the tools from friends, friends or comrades.