"Agidel" (pump): specifications and instructions

If you are looking for a popular surface pump, which is now in demand by summer residents, then you can prefer "Agidel". Even if there is a central water supply in a private area, the owners of the houses quite often prefer to have equipment at hand that allows you to water the beds with water not from the tap, but from the nearest well. With the help of this device it will be possible to use rainwater for irrigation of crops, which is collected during the period of precipitation in the tank.

After reading the article you may be interested in the "Agidel" model. A pump of this type, according to users, is ready to serve for a long period of time. Before purchasing it is necessary to find out under what conditions it is possible to operate this device.

Main technical characteristics

The model described refers to a surface version of centrifugal pumps that pump water without immersion in a liquid. The device will need to be installed near the source, putting only pipes or suction hoses into the water. This will ensure a high level of safety, since the contact of electrical wires with liquid will be completely ruled out.

Features of the model "Agidel-M"

If you are interested in the Agidel model, you can purchase a pump of this type at an affordable price. The above-mentioned variety is distinguished by its small dimensions, as well as very economical energy consumption. Thus, the device weighs only 6 kilograms, and the consumption is 370 watts. This equipment is intended for pumping cold water, its temperature should not be more than 40 degrees. You can use this device to pump water from a depth that reaches 7 meters. At the same time, the equipment can operate for a long time without stopping, which is provided by protection against overheating.

If the unit is completed with an ejector, then it can easily be used in wells, the water mirror in which is located at a depth of 15 meters. If you are considering the Agidel model, a pump of this type can be used to pump exceptionally clean water from swimming pools, wells, artificial ponds and wells. If you plan to pump water from a reservoir or pool, you need to ensure that from the intake valve to the bottom was more than 0.35 meters. The most impressive water pressure is 20 meters.

Characteristics of the Agidel-10 pump

This equipment differs from the above-described model in that it is more powerful. This unit consumes 500 watts during operation, but it can provide a more impressive head of water, which is 30 meters. Weighs such a device 9 kilograms and acts as a self-priming pump. The equipment does not presuppose the need to fill the water when the system is started up.

If you decide to choose Agidel, the pump of this brand is very reliable, as users note. It can be used to conduct water supply to a residential building. This is due to the fact that the equipment has a high power and supplies the liquid at once to several points with a normal set. Thus, at the same time water can flow both into the kitchen and into the bathroom.

User's manual

The "Agidel" pump, the characteristics of which you will be useful to know before visiting the store, should be installed exclusively on a flat and firm surface. It is from this circumstance that the quality of the work in use will depend. It is important to take care of protection against direct UV radiation, as well as rainfall. Experts recommend to equip special containers or install equipment inside the utility room. The first method is more preferable, because due to the long hoses and pipes, the water head prescribed in the instruction will be reduced.

Recommendation of the master

The "Agidel" pump, the characteristics of which are described in the article, is not intended for use in winter, but if there is no other option for water supply, it is necessary to find a room in which the temperature will not fall below zero. However, you can use an alternative method, which involves digging a pit. It should be located below the freezing level of the soil, concrete, and then heat insulated, placing the equipment there.

Additional recommendations for use

The water pump "Agidel" can be installed inside the well itself. This is what some lovers of holiday homes do. To do this, you will need to build a strong raft of materials that do not interact with the liquid. This approach allows you to artificially increase the suction height, but assumes the need to connect to the extension cord. This requirement is due to the fact that the length of the cord will not be enough to reach the outlet.

It is worth remembering before the installation works that the length of the cord from the pump is only 1.5 meters. The Agidel water pump must be installed in such a way that the connection point to the extension cord is carefully isolated from the effects of moisture. The installation of the equipment must be done with the obligatory grounding.

Pouring before starting

It is necessary to take into account the fact that the connection of the Agidel-M pump requires preliminary water pouring. Such a requirement is explained by the fact that functioning dry can cause a breakdown of the whole mechanism. It is important to consider the technology by which you can make the system fill with water at the dacha by means of a hand-held column. Pumps "Agidel", the technical characteristics of which allow you to perform the installation correctly, should be filled before starting the operation. To do this, open the tap, and then lower the hose from the equipment into the container with the liquid.

In order to create a vacuum in the borehole, you need to start swinging the column. By means of a pump hose, the liquid from the tank will flow to the well. This will cause the movement of the air impeller of the equipment. Once the water has drained from the column, it will be possible to start the unit. The scheme of the Agidel-10 pump does not imply the need for pouring. The fluid at the first start should not appear immediately, it will happen within 5 minutes. This is the difference between self-priming systems. It is worth remembering that the higher the liquid level in the well, the faster the water will flow.

How to troubleshoot pump problems

The instruction manual is included. The "Agidel" pump will work properly if you follow the rules prescribed by the manufacturer. If you notice that the water supply is very weak, then the reason for this can be using an incorrect hose for water intake. If water is sucked from the well by means of a rubber device, then rarefied air can be formed , which leads to compression of the walls. This can interfere with the normal supply of fluid. Experts recommend using a hose that is reinforced with a plastic spiral.

So, you purchased the device "Agidel". Pump, spare parts for which you can purchase from the supplier, will serve you for a long time. To exclude the possibility of its imminent breakdown, care must be taken to ensure proper operation of the equipment. The current repair of the device is associated with the replacement of oil seals, as if they fail, you may encounter a leakage problem in the drainage hole.

To replace, you need to unscrew the 3 bolts that are located on the body. The master must remove the cover and unscrew the 4 bolts that are located in the engine. Further, you can remove the motor housing, detach the cochlea and unscrew the bolts. The master will need to remove the gasket and unscrew the nut holding the impeller. Then the anchor is removed, which can be assisted by a hammer blow. After he came out of the hull, you need to find the oil seals in the impeller. They are removed in such a way as not to damage the insert between them. At the final stage, you need to install new seals, which are separated by an insert. It is necessary to assemble the pump in the reverse order.

Conclusion

The described "Agidel" pumps are reliable and high-quality equipment. In order to ensure long-term operation and the possibility of stable pumping of water in any period of the year, it is necessary to use the device in accordance with the instruction. However, in addition you will need to lubricate and clean individual parts.

All these manipulations you can produce independently, without resorting to the help of professionals. This helps to save a fairly large amount of funds. However, if you need to seriously repair the equipment, then in this case it is best to contact the service center. This will prolong the warranty and will not cause a more significant breakdown, which you can face, doing repairs yourself.