Protection of the bumper from stainless steel - manufacture and installation by own hands

The protection of the bumper from stainless steel is a multifunctional detail of the vehicle. Basically, this equipment is required for unimpeded movement of the car on the road. In addition, the device allows you to pull the machine out of a sufficiently deep gauge by raising it and rearranging it. Also, when replacing one of the wheels, you can lift the vehicle and quickly make a replacement. In addition, the protection can be installed additional lights, which improve the driver's view at night.

Device Advantages

The protection of the front bumper in stainless steel has several advantages. First of all, such a detail performs a decorative function. If there is an opportunity to acquire protection, then the assortment of such products is quite large. The car owner can buy a detail of any shade and texture.

Another advantage is durability. If the stainless steel protection is properly coated, it is possible to obtain a part that has chemical resistance and is resistant to mechanical damage.

In addition, such a device is simply necessary for those who are forced to ride off-road.

Buy or make

The protection of the bumper from stainless steel allows you to avoid accidental raids on the curb, as it is envisaged the installation of an additional detail of metal - kangurin. Initially, such devices were used only for SUVs. However, in recent years, such protection has been installed on other models of cars. Ready-made kit to find on sale is almost impossible. Extended protection looks quite good on minibuses, as well as on off-road vehicles. For cars of other classes, such accessories are not manufactured. If the desire to decorate the body of your vehicle is not lost, then you can try to make protection yourself.

Main stages

So, how is the protection of the bumper made of stainless steel with their own hands? The whole process consists of several stages:

• Measurement of the front or rear bumper of the vehicle;
• Drawing up a scheme corresponding to all parameters;
• Preparation of tools and material;
• Manufacturing of kangaroo;
• Accessory installation.

First stage

First of all, it is necessary to determine the variety of kenguryatnik. A certain model is provided for each class of vehicles. After determining the model, a small sketch should be made.

If necessary, you can contact a specialist. They will help you determine which type of protection is right for your car. When the circuit is ready, it is necessary to carefully measure the front of the machine. The received parameters should be transferred to the scheme. When choosing a model, one should take into account that more complex manipulations are needed for a more complex drawing.

Preparation of materials and tools

The most common protection is for a bumper made of stainless steel. This material is much more practical than other metals. Painted pipes after several trips require updating the paintwork. This is not required for stainless steel. With proper care, this metal keeps its appearance well. In addition, the stainless steel accessory looks more solid. However, it is worth considering that such a metal is much more expensive than other varieties.

In addition, the quality of the joints of individual parts and the overall appearance of the structure will depend on which welding machine will be used during operation. Polishing and grinding of pipes into a single whole is possible only with a special argon-arc unit.

If at hand there is no such device as a pipe bender, you will have to purchase several corner-folds. The angle must be 90 ° and 45 °. The choice of corners depends on the complexity of the structure. It may also be required pipe cutter and Bulgarian.

The process of manufacturing individual elements

Making a bumper protection from stainless steel is a process that requires patience. To begin with, it is worthwhile to prepare individual parts of the structure. To do this, on the pipes and corners it is necessary to make the appropriate markings, and then with the help of the Bulgarian it is necessary to make incisions in places with marks. In the manufacture of protection, one main rule - symmetry - must be observed.

At the junction of the main pipes and T-shaped bridges, it is worth leaving a small gap, about 1 millimeter, but no more. To do this, use the pipe face. When the preparation of all the elements is completed, you need to carefully inspect them and check again the symmetry.

The final stage of manufacturing

Protection of the bumper from stainless steel to duster and other models must be manufactured in accordance with the finished scheme. At the next stage, it is necessary to make a marking of the intended attachment point for individual components and jumpers. This will save considerable time during welding. When everything is ready, it remains to begin collecting the structure. For this, it is necessary to pick up individual elements in the marked places by welding. In the end, the design should be polished. It is recommended to start with folds. Such places are best suited to such processing and are located separately from the main structure.

After that, once again check the elements for compliance with symmetry. Only after this, each part can be welded by argon-arc welding. The protection of the bumper is made of stainless steel.

Installing an enhancement

The lifespan of protection directly depends on how it is secured. A guideline for welding 2 thick pipes leading to the longitudinal members, to the kengurin will be the distance between the side members of the vehicle. Do not forget about the mounts. They should be fixed at the ends of these pipes. To this end, according to experts, the plates are ideally suited for about 10 millimeters with bolts, the marking of the holes is designated M12 and M10.

To perform the next step, second hands will be required. The finished structure must be attached to the front of the vehicle, leaving a gap of no more than 10 millimeters from the bumper. Place the mounts against the side members. It is important. Through the holes in the mounts, it is worth noting places for holes on the spars, and then you need to drill them. After that, the bolt is bolted. Do this yourself will not work.

Specialists do not recommend tightening the protection for the bumper in stainless steel. This makes no sense. Kangarin with a strong impact should bend itself, protecting from damage to the side members and the frame of the vehicle. In SUVs and minivans, such protection saves the headlights from mechanical impact.

In conclusion

The protection of the rear bumper in stainless steel is made according to the same scheme. The only thing to consider is the size and shape of the finished structure. These parameters differ from those of the front kangurin. If there is no ready-made scheme, then it is worthwhile to turn to specialists for help. For more wealthy car owners, there are ready-made models. Very popular is the protection for the front and rear bumper made of German-made stainless steel.