Liquid acrylic for bath: reviews. Restoration of the bath with liquid acrylic

Over time, the coverage of any bath can become worthless. It is not so easy to restore it. Recently, liquid acrylic for baths is very popular. This tool allows you not only to return the gloss to any product, but also to remove small cracks and chips. Restoration with liquid acrylic is considered the most effective method. For the first time this tool appeared on the market in 2009. Liquid acrylic has become a sensation. After all, it has many advantages.

Preparation of a bath for restoration with liquid acrylic is very simple

First of all, before the application of the product, heavy preparatory work is not required, for example, the dismantling of the bath. In this case, do not carefully remove the yellowness embedded in the coating.

To eliminate on the old enamel all kinds of cracks, you can use ordinary carpeting for cars. In addition, before applying acrylic, it is possible not to remove rust by various special solvents, as well as converters. It is enough to walk along the old layer of the enamel with sandpaper.

A little advice

Liquid acrylic allows you to completely restore the surface of the bath. However, to make the coating smooth, it is worthwhile to seriously approach the preparation of the product. After treatment with sandpaper, the bath should be washed with warm water and detergent added.

When buying all the materials necessary for the restoration of bathtubs, special attention should be paid to liquid acrylic. Choose only long-lasting. Due to the composition of such a mixture, the final coating will be much stronger. At the same time, this acrylic will last longer.

After finishing all work, the bathroom should be closed to eliminate any air swings, insects and dust on the fresh cover. Dry the product after restoration should be no less than four days. In some cases, it takes a little longer.

After the restoration of the bath in the room it is necessary to maintain the temperature within 17 - 25 ° C above zero. Install the overflow and drainage siphon only after the new coating has dried completely.

Liquid acrylic: dignities

The most important advantage of this material is the high strength of the coating that it forms. This is achieved thanks to a layer of 6 millimeters. It is worth noting that the product, covered with liquid acrylic, is able to withstand even a hammer blow.

Another advantage of acrylic is its low thermal conductivity. Usually, the bath is made of steel or cast iron. However, such products have a sufficiently high thermal conductivity. For example, in a bath of cast iron, water will cool down in just 4 minutes per degree. As for acrylic, this material, on the contrary, does not allow to cool the contents of the bath. The water in the product with such a coating will cool more slowly: one degree - 30 minutes.

In addition, the surface covered with acrylic, much longer remains white. Over the years, the bath begins to turn yellow. However, the products covered with acrylic, the longer the rest please their owners with pristine whiteness. But that's not all. A layer of liquid acrylic is resistant to chemical detergents, which can also be considered one of the advantages of this coating.

Another advantage of the substance is its durability. Usually an acrylic coating is given a guarantee, which is calculated for about 10 years. In this case, the product can be used daily. The material does not lose its practical and aesthetic qualities.

How best to prepare a bath

So, liquid acrylic, the price of which depends on certain parameters, does not require special preparation of the product before application. However, you still have to prepare a bath. To do this, you should buy a usual cleaner, as well as rubber gloves, drill bits, sandpaper and spatula. When all the tools are at hand, you can start working.

Using a brush and a cleaning agent, you must thoroughly wash the bath. This will eliminate stale dirt and limescale. Also for this purpose, you can use ordinary baking soda. In this case, the bath will also be defatted.

After that, it is necessary to remove all the decorative overlays on the overflow and drain hole. Place their installation should be cleaned from rust. For these purposes, it is better to use sandpaper. If necessary, special drill bits can be used. This will remove the highly stale rust.

In addition, it is worth going through sandpaper on all slopes of the product. In this way, it is easy to remove pieces of lag behind the walls of the enamel. If necessary, you can use a spatula.

If during the operation or during cleaning on the surface of the bath there are potholes, they should be puttied. After drying, all the places must be cleaned again. In this case, it is necessary to use automotive polyester putty or epoxy resin.

After preparation, the product should be washed with running water. But that is not all. Specialists recommend to collect warm water in the bath, and then drain it in 10 minutes. This will allow the material to warm up. This is best done before applying liquid acrylic.

Then the product should be dried dry and dried. To do this, you can use a building hair dryer.

We begin the restoration of the bath

Repair of baths with liquid acrylic takes a long time and requires patience and accuracy. You can start work only after the coating is ready. In the dishes with a polymer base, you need to add a hardener, and then mix everything thoroughly. It should be noted that the mix should be mixed for 12 minutes. Otherwise, uncured liquid acrylic will remain on the surface of the bath.

A portion of the finished mixture, approximately 1.5 or 1 liter, is poured into a separate container equipped with a spout. If you do not have one, you can do it yourself. To do this, in a conventional plastic bottle, cut the neck.

In the prepared dishes you need to pour diluted liquid acrylic. After this, you can proceed with the restoration of the bath.

How to cover a product with acrylic

Begin from the corner of the bathtub that adjoins the wall. It is necessary to create a layer of liquid acrylic about 5 centimeters. In this case, the substance must freely flow down the slopes of the product to the middle. To move along the perimeter of the bath you need to gradually, evenly distributing the mixture. It must flow unhindered. It is necessary to move only along the perimeter of the bath. In this case, you should be careful not to allow excessive pouring.

When the perimeter of the product is completely covered with liquid acrylic, it is impossible to add the mixture to the already restored parts. Otherwise, an ugly leak develops. The coating of the bath with liquid acrylic does not end there.

The next circle should start from the middle of the slopes of the product. At the end of the restoration, a too thick layer may form on the bottom of the bath. It should be leveled with a spatula. You need to move in the direction of drainage. This will remove the excess mix, draining them into the sewer.

It is strictly forbidden to touch the spatula against the sides of the bath. This can lead to a violation of the integrity of the new coating. It is worth remembering that all the influx will go away on their own.

Some caveats

Liquid acrylic for baths should be used neatly and very quickly. All work on restoration should not last more than 4 hours. When applying liquid acrylic, do not make long stops and large breaks. Of course, without the experience of such work, the restoration of the bath will take a long time. However, it is worth remembering that the masters of coating products with liquid acrylic takes only a few hours.

User Reviews

Today, for the restoration of bathtubs, many choose liquid acrylic. Reviews about this tool are mostly positive. Most people note that their bath has acquired a snow-white shade. The main thing - to apply liquid acrylic gradually, observing all the rules. In addition, many consumers indicate in their feedback that the coating is stable not only to the effects of household chemicals, but also to mechanical damage. But the decrease in thermal conductivity allows longer than usual to luxuriate in warm water. Negative feedback on liquid acrylic is a rarity. Basically, they are associated with improper application of the mixture.

In a short time without dismantling and exhausting preparation of all surfaces, you can get an updated bath that does not differ from the new one.

The cost of liquid acrylic

Liquid acrylic, the price of which depends on the capacity and the qualities of the hardener, can be purchased in many construction stores. It is usually sold in buckets of plastic. At the same time, the capacity of the container is not less than 3.5 kilograms. As for the hardener, it is sold exclusively in half-liter bottles.

It should be noted that this amount of materials will be enough to cover baths made of any metal with a length of 1.7 meters. As for the cost of liquid acrylic, then on average, it is 1100 - 1800 rubles per bucket. If you are not confident in your own abilities, then you can hire specialists of the company that provides services for the restoration of baths. Of course, it will cost much more: about 3500 rubles.