Installation of gates on the front door: types and methods

Quite often, when installing the front door, there is a need for mounting of the gates. This device brings the opening to perfection, and if you use it in combination with other components, the design will look complete.

Varieties of door accessories

Before you will be installed installation on the front door, you need to familiarize yourself with the technology and understand the main varieties and design of these elements. Docks represent some part of the door frame that connects this element with the platbands. The need to close the wall in the opening can arise when the wall thickness is larger than the box itself. To do this, you can apply the straps attached to the box.

If you will be installing the gates on the front door, the types of these elements should be considered. Among them are those that are made of:

• MDF;
• Wood;
• Metal.

Docks may have an edge or be deprived of it. Telescopic elements are another type of dobor. The first option is the simplest and is presented in the form of a strip without treated edges. Sections at the final stage are closed with platbands, but this can negatively affect their durability if the humidity level is too high.

A simple cutter with a lip has edges treated with a protective coating, which prevents water from entering the internal structure of the material. Telescopic selection is the most convenient option. It has machined edges and spike-groove connections that allow mounting on door frames and casing.

Need for use of tools

The installation of the dongle on the entrance metal door is carried out when it is necessary to increase the box in the coverage area. These elements can expand the door frame. Planks you can buy with the door unit or separately. Complex design, they do not differ, so you can make and install them yourself.

Methods of assembling the tools

The door can be installed on the entrance door using one of several technologies. You can do this to the door box, to the mounting bar and to the wall in the opening area. The second method assumes the need for a mounting beam between the dowels and the vertical planes of the opening.

Advice for the installation specialist

When the installation of gates, clysters on the front door is being conducted, you may encounter a problem when the box is not able to cover the width of the opening. This part can be pasted with wallpaper, covered with plaster or trimmed with plastic. But the use of dobors allows you to achieve a better result, because the elements look more attractive, but they are cheaper and do not involve repair.

The beam of the box can have a selected quarter for mounting. If there is none, then the equipment may have any thickness. If this assembly recess is present, then installation of the door entry can be conducted , the dimensions of which are 1 cm in thickness.

For the reason that the docks will not be affected by mechanical stress, only liquid nails are used for fastening. However, the most common can be found as fasteners galvanized self-tapping screws. If the fastening is carried out from the outside, then the caps should be closed with plugs or mastic.

Carrying out the installation of the tools

You can purchase a door frame with the base quarter or without this device. In the first case, the installation will be fairly simple. To do this, use wood-based or wooden strips. Their width should be measured after the box is already in place. After the entire structure has been assembled, the end line of the dash must be flush with the opening line.

If you notice surpluses, then you can remove them by plane, and then zaderkorirovat cashing. Expansion of the door structure by dowels is sometimes carried out using galvanized 25-centimeter nails. This case applies to doors with a groove. For fastening, you can use glue, which is applied to the recesses of the box.

Installation of gates in the opening with an extension

Sometimes it is required to install the gates on the entrance door with their own hands, when the opening has an extension. For finishing, you can use one of two methods. The first involves gluing along the perimeter of the bar, the length of which can vary from 30 to 40 cm. Next, a box is installed in the box, and the formed space is filled with construction foam.

The second method involves the need to screw the bar to the wall with several screws. With their help, you can adjust the position of the resulting frame, and then install the fitting in the groove and fill the installation gap.

Installation of gates in a box without excavation

You can select a quarter using a milling machine, however, for this you need to pre-assemble the ruler and use a straight cutter. Once the box becomes part of the door element, you can proceed with the installation of the device. Its fixing is carried out through the holes made by screws, which will be located from the butt. The diameter of these holes will not be the same over the entire length.

To start, the master should use a drill, the diameter of which is equal to the diameter of the self-tapping screw. The next step is to use a drill with a diameter equal to the size of the barrel. The installation of the gates to the entrance door is accompanied by the installation of a vertical bar, which must be remote from the floor surface by 20 cm. The elements are then reinforced after 55 cm. The accessories can be placed together with the box inside the base of plywood or plasterboard. A box can be connected and without a quarter, using the slats of the dobors and racks. These elements are not strengthened by a continuous strip, they need to be installed in separate segments.

Tips for strengthening the gambling among themselves

The installation of the gates on the entrance door must be accompanied by the fastening of the elements among themselves. To do this, use galvanized self-tapping screws. If it is a matter of MDF elements, the fastening holes must be made in advance, so that the material is not damaged by twisting.

The holes must be punched with a drill, the diameter of which will be 3/4 of the diameter of the screw. If it is a question of wood-shaving materials, the self-tapping screws should be cut all over the trunk.

Classic scheme of installation of the tools

Installation of the gates to the entrance door is carried out according to a certain algorithm. First you need to make measurements, drawing attention to the fact that for the right and left doppler measurements on the vertical should be carried out separately. The inner line of the vertical bar must be measured by the box.

To the installed door frame, it is necessary to fix the three additional parts. Between the dowels and the wall, it is necessary to place mounting wedges, the position of which can be changed to align the structure. Before filling the gap with mounting foam, spacer wedges need to be installed between the dowels and the bollard.

Conclusion

Inhibition should be performed portionwise. It is best to do this in two steps. The solidification process in this case will be controlled. If necessary, it will be possible to make adjustments until the composition is completely solidified. The work should be completed by sealing the gap between the floor covering and the wooden parts. At the final stage, the platbands are installed.

Sometimes the false base is made not only from plasterboard, but also from magnesite plates, moisture-proof plywood or OSB. The flaps of the block bar can be fixed in increments ranging from 25 to 30 cm. The top panel, which will be placed horizontally, should be laid on vertical elements.