How to weave a bracelet of rubber bands on the machine? From the simplest to the most complex

Small rubber bands are increasingly becoming the basis for all sorts of jewelry. It is not difficult to master different techniques. It is enough to understand the basic techniques - and soon it will be possible to independently explain to the beginner how to weave bracelet from the rubber bands on the machine or without it.

The easiest bracelet on two machine pegs

It can be a large machine, but you only need to use two of its pegs, or a special small one, called "slingshot". This technology will be understandable even for beginners. Because in order to weave a bracelet out of rubber bands on the machine, it is enough to remember the beginning of the work and the basic principle.

The first rubber should be twisted by a figure eight. Then it should be put on two adjacent pegs of the machine. In the place where it is twisted, snap on the S-shaped buckle. This is the beginning.

The continuation of how to weave a bracelet of rubber bands on the machine, is as follows:

• To put the second rubber on top of the first, but it no longer needs to be twisted;
• Remove the lower rubber band from the left and right pegs by means of a hook;
• Repeat the first two steps as many times as necessary to get the chain of the desired length;
• To throw the last loop on one peg;
• Hook them with the clasp that was used at the beginning.

Bracelet "French braid", woven on two pegs of the machine

Its production is similar to what was described for the previous version. It is somewhat more complicated, but still, how to weave a bracelet out of rubber bands on a machine, for beginners should not be very difficult.

The beginning of weaving is the same. Then all the rubber bands are attached without twisting. In how to remove them from pegs, and the differences begin:

• Put on two rubber bands;
• Remove the lower elastic band from both pegs;
• Put on another rubber band;
• From the left to remove the lower elastic band, and from the right one - the middle one;
• Put on a rubber band;
• From the left peg to remove the middle peg, and from the right peg to the bottom peg;
• Repeat the 3-6 action until the bracelet is the right length;
• Remove the lower rubber bands from both pegs;
• To throw an elastic band on one peg;
• Fasten the clasp by closing the bracelet into the ring.

It looks very impressive, if you use two or three colors of rubber. In this case, alternate them in a strict order.

Bracelet "Sidewalk"

He again paddles on two pegs of one machine. Only the volume and thickness increase due to the use of double rubber bands. Work on it is similar to the previous two. But, as usual, there will be a difference. The beginning of how to weave a bracelet of rubber bands on a machine, is the same. Only roll up the figure eight you need two rubber bands.

The technology of making a bracelet boils down to the following:

• Two rubber bands of a different color;
• Remove the bottom two from the right peg;
• Put on two new rubber bands;
• From the left to remove the four lower;
• Repeat the third action;
• From the right one, remove the lower four;
• Repeat 3-6 points until the required length of the bracelet is obtained.

Clamp it in a ring by the same principle that is indicated for the two previous types of bracelets. You can already talk to your friends. Jewelery on the pens will be enough.

Bracelet "Zigzag from squares"

For his weaving will require the entire machine. Its rows should be fixed in the same way to make a rectangle and all the pegs stood one above the other.

Before weaving a bracelet from the rubber bands on the machine, it should be arranged so that the round part of the pegs looks at the needlewoman. The order of the rubber bands should not be violated. Otherwise, the bracelet will collapse at the very last stage.

• On the central row connect the first two pegs.
• The second rubber band must connect the two lower pegs of the machine to the left.
• Then on the left row the first two.
• Close the rubber band square.
• Repeat all actions, but only on the right side, starting the square from the upper right corner of the already existing square.
• Then again the square on the left. And so to the end of the machine.
• On the last used peg put on a rubber band, twisted twice.

Turn the machine so that its pegs look at the needlewoman with depressions. Now you need a hook, which will need to remove all the rubber bands in the reverse order. And to pass it is necessary on three external sides of a square, and then to remove a rubber, which is in the central line.

Put on all the rubber bands of the last peg clasp. Carefully remove the bracelet from the machine. It can turn out that it will not be enough length for the girl's wrist. Then on the end free from the fastener you need to weave a chain. Then close it in the ring.

Bracelet "Starry"

For him, the central row needs to be shifted down. Place the machine as in the previous case. Now you can figure out how to weave a bracelet of rubber bands on the machine. Schemes of this begin with circumvention of the machine along the perimeter.

First from the central lower peg to the left and to the end of the machine, leaving the latter free, and to the last peg in the center row. Then also on the right side of the machine. Lower all the rubber bands from the top of the peg. This will be required for convenience in further work.

On the three central pegs and four on the sides make the first star. To do this, you need to put the rubber on the center of them and each in a circle. You need to start with a pair of second pegs of the central and right rows.

Make such asterisks on the whole machine. They must come into contact with each other. Now you need to take twisted rubber and put it on the last central peg. The same action should be done for each center of the stars.

Turn the machine over. Start braiding the bracelet. First remove the rubber from the central peg. Then move counter-clockwise and remove everything only for the first star. Then, too, do with the second-generation rubberies and so on.

Now it's the turn of the perimeter. It must also be weaved. Start from the bottom two, going from the central peg to the left and to the right. Then walk along the sides and finish with the upper ones, directed towards the central one. Through all the hinges on the last peg stretch the rubber band and fasten the clasp on it. The bracelet can be removed. If it is small, then do the same as it was indicated for the previous one.