How to transfer drawing from paper to paper and to other surfaces

If you do not know how to draw, but would like to learn, you should start with a simple - copy drawings. For a start, you can do this with tracing paper. This method is the simplest in execution. Now let's more accurately study how to transfer the drawing from paper to paper.

Instructions

To transfer a picture, follow the sequence below:

1. We select the image and, putting a tracing paper on it, we tighten all lines using a black acrylic handle.
2. Now turn the tracing paper and put it face down on the sheet of paper to which you want to transfer the image.
3. Tightly press and pass on it with a hot iron.
4. Now we remove the tracing paper and in addition draw insufficiently sharp lines.
5. The image is ready.

This method is used for simple pictures that do not contain a lot of complex details. Now you know how to transfer the drawing from paper to paper in a simple way. Try it, you can proceed to others.

A more complicated way

To transfer complex drawings, you can use the mesh to copy. With its help, it is also possible to reduce or zoom the image itself.

Looking for:

• Original drawing;
• transparencies;
• Capillary handle ;
• paper;
• duct tape;
• Ruler;
• pencil.

Instructions

To master this method, follow these steps:

1. On the original image we put a transparent film on which squares of the same sizes are represented.
2. The same cell is applied to a blank sheet of paper, if the picture is reproduced in the original. How to transfer a drawing from paper to paper, when the size of the image needs to be changed? With increasing the sizes of squares do more, when we reduce, respectively, less.
3. Now all you have to do is transfer the image to the cells.
4. When the picture with the help of a pencil is completely transferred, you can start to paint.

Now you know how to transfer the image from paper to paper. Let us consider other surfaces.

Body as a foundation

The tattoo is a highlight of the exterior, but not everyone decides to apply a pattern to the skin, realizing that this decision is taken for life. For people who are afraid of such an act, but they want to decorate their body with a beautiful image, temporary tattoos are an excellent solution . To learn how to transfer a drawing from paper to the skin, you need to study the following information. The main stage is a clear drawing of the contours of the future image.

A picture can be applied to the body using:

• Copy paper ;
• Tracing paper.

The first way

For him, you need to do the following:

1. The choice of the picture, the location of its application, the disinfection of the skin.
2. Transfer of the image to the carbon paper. To do this, put the paper on the original and carefully draw all its contours.
3. We moisten the carbon paper with alcohol and apply it to the body.
4. To make the contours well imprinted, circle them again through the carbon paper, trying to leave it whole.

The second way

It is based on the use of tracing paper. It is necessary to do the following steps:

1. Draw the helium pen itself drawing.
2. We disinfect the skin and soap with soap.
3. We apply tracing paper and circle the contours with a sharp object.
4. Now we paint the picture.

If you still decide to put a permanent picture on your body, approach it very carefully. The main thing is to choose a good salon, pass the test for an allergic reaction and check that all the instruments have been disinfected.

How to transfer drawing from a paper on glass

For work, we take an image with good contours and a roll of food film. For transfer, you need to buy a marker-marker for glass, it falls well and is easily washed off the surface.

Instruction:

1. We take the film. Its size should be slightly larger than the figure itself. The film is attached to the surface, which prevents the picture from straying.
2. The image is put on film and it is guided thinly and very accurately.
3. Now the film is accurately transferred face to the previously prepared surface. Preparation is to degrease its front side. Make sure that the film is completely stuck to the glass, get rid of wrinkles and bubbles.
4. For a more precise transfer, draw the image again around the contour with any sharp object.
5. It's time to get rid of polyethylene. This is done very carefully so as not to smear the picture. If there are inaccuracies somewhere, now is the time to fix them.
6. Now draw the outline. This can be done with acrylic paints and brushes.
7. After all has dried up, carefully with cotton balls, moistened in liquid, we get rid of the traces of the marker.
8. Inside the image is filled in any way. If the technique is stained glass, then everything is poured along the contour.
9. After drying for a longer service life, the image can be baked or varnished. It all depends on where this item will be used.

How to transfer drawing from paper to wood

In order to see your favorite image on a wooden basis, you just need to follow the steps below.

You will need:

• A drawing printed on a laser printer;
• wooden plank;
• Acrylic gel-medium;
• Flat tool for leveling the pattern;
• Paint and rag;
• Soft paraffin or matt glue;
• 2 brushes.

Instruction:

1. Select an image. It should be a drawing that will look nice on a wooden base. To give some resemblance to the vintage style, it can be processed in special programs.
2. The image is printed only on a laser printer, this is the main condition.
3. A smooth wooden base is chosen.
4. Now we apply a uniform layer of gel-medium. It will help the image to be transferred to the prepared surface.
5. We have the picture face to face. At the time of the connection, bubbles arise which, if possible, should be smoothed.
6. For today the work is finished, leave everything for the night, tomorrow continue.
7. It's time to remove the paper. To do this, you need to wet and wipe it with your fingers. Right now you are witnessing a miracle - when you remove the paper you can see how the image remains on the tree.
8. Now you can use the paint for the tree. Keep track of its number so that the image does not darken.
9. Now apply liquid paraffin. If necessary, the last two steps can be repeated after the first layer has dried.

Other basics for image transfer

Metal is the base, also suitable for such "tricks". To accurately and accurately work on it, draw two axial lines or mark the corners of the image. Now consider in more detail how to transfer the drawing from paper to metal.

The most common is the use for this copy paper. Since metal is a very hard material, it is covered with white or light paint. The process of transfer begins after the complete drying of the varnish, which is applied before the very beginning of the main work.

Instructions

This method requires the following rules:

1. The picture is very tightly attached to the product. To do this, you can use a soap solution.
2. Many masters for this work use chasing-kafarnik. With him, the image is very accurate - almost a piece of jewelry, which, however, takes a very long time and requires some preliminary training.
3. The instrument is taken with three fingers, resting on an anonymous one, which serves as a kind of spring. The coin is located 2-3 mm from the figure, its light strokes form a dotted line - the main outline of the image is drawn. The smaller the detail of the picture, the denser it gets.
4. When all the lines are transferred, you can wash off the paint.
5. The image can be varnished.

Now you know how to transfer the drawing from paper to paper, to leather, glass, wood and metal. Forward - for the tools, and good luck in your endeavors!