How to remove the "red" from the body of the car yourself

Corrosion of metal is the most dangerous "disease" of a mechanical device. If it is not rectified in time, then a small dot will soon turn into a bloated paint, and eventually a hole will appear. You can use the methods how to remove the "redheads" from the body of the car in the garage conditions. However, following the instructions, it is recommended that you already have some metal painting skills. Otherwise, unsuccessful attempts will lead to costly repairs.

Where does corrosion come from?

With each used car, the protective metal layer chips eventually appear. Owners are beginning to wonder how to remove the "red" from the body of the car. After all, if you do not take measures to restore the paint, the corrosion will begin to spread deep under the influence of moisture and aggressive environment.

The question of how to remove the "red" from the body of the car, begins to worry drivers in the spring. Over the winter, defects in lacquer coatings are swollen in both old and new cars. The reason for the formation of corrosion are the temperature drops of heated air from the passenger compartment and from the street, from the engine or damage from the reagents that have fallen on the paint. The latter are applied to the coating to eliminate ice crust.

Steps to repair a defect

Consider how to remove the "red" from the body of the car. Stages of repair:

1. Inspection of paintwork.
2. Cleaning of the rusted surface: mechanical and chemical.
3. Application of fixing layer, binding metal and putty.
4. Preparation and priming of the surface.
5. Paint by spray gun.
6. Polishing.

Do not forget about maintaining the appropriate environmental conditions:

• About 25 degrees, so that the applied mixture dries.
• Low humidity in the room.
• Absence of suspended particles, dust. This applies to the painting stage.

The listed conditions are preserved in the advanced auto repair shops. You can entrust the work to professionals, they know better how to remove the "redheads" from the car, but if you want to save it easily, doing all the steps yourself.

Inspection of defects and cleaning

It is sometimes difficult to notice slight corrosion. In order not to miss insidious specks, it is better to wash the car on a sink with the means.

Survey the surface in daylight, preferably outdoors, in sunny weather. Tiny damage to the paint can be immediately eliminated with a varnish, suitable nail polish.

In the formation of deep rust, two methods are used:

• Mechanical - clean rags, remove the deep layers nazhdachkoy. Suitable nozzle with a drill, it will save time.
• Chemical - a special substance, a rust converter is applied to the corroded area , the reaction residues are washed off with water.

Before you remove the "red" from the body of the car, you should thoroughly assess whether there are all the necessary substances and conditions. After cleaning, the surface should be mirrored and not contain brown spots.

Putty

So, we coped with the sweep, choosing the way how to remove the "red" from the body of the car. The photo below shows what should be prepared for the next stage of the surface.

The resulting area is required to be washed from the crumbs of the old paint. It is necessary to degrease the surface with alcohol, it will quickly dry the remaining drops of water. Naked metal can be lubricated with a binder, but this stage is usually not performed. Immediately proceed to applying the mixture to the metal.

Putty can be prepared, but it is better to buy ready. It dries quickly after adding the fixer, so apply the mixture quickly. Avoid the formation of excess material, so as not to spend a lot of time on stripping. Smooth surfaces are achieved using a rubber spatula.

Putty will not be a thick layer. Over time, it will crack from the vibration of the body, and the top coat with paint will have to be remade. Strongly damaged places are cut off by the Bulgarian and fresh metal is welded.

Preparation for final painting

So, we remove the "red" from the body of the car. Instructions for painting the body indicate the inadmissibility of residual rust. The coating will necessarily swell the next spring. After the putty has dried, the treated area is first cleaned with a coarse, and then with a small emery, until a smooth surface is obtained.

When stroking, there should be no scratches, dimples, swings. When the paint falls, even the smallest error will be visible. Therefore, they achieve an ideally smooth base for the next step - priming.

The primer is applied by the spray gun in the same way as the paint coating. It penetrates deep into the layers of putty, creates a rough and firm foundation. It is necessary that the drops of paint do not roll down.

Painting

Before applying solutions it is recommended to use paint tape and film to protect a good surface, glasses and rubber bands. Remove the coating immediately after leveling the putty, spraying the paint. However, at the time of the last operation, the strips are glued at a distance from the treated area. This is necessary for a smooth transition.

Old paint and new will have differences in any case. Just pick up the color can only experienced colorists. No less knowledge is needed and the painter. It is important to spray the finished solution in several layers, without the formation of streaks.

To get an ideal and not different from the old paint area, use a heater. A similar convector with a reflector is used in medicine. Completion of the efforts becomes the treatment of the body polish, which will be selected in the auto cosmetics store. Or it is necessary to apply a new paint and varnish completely on the whole surface, which is much more expensive.