Drill for ceramic tiles. How to drill a ceramic tile? Drills on glass and ceramic tiles (photo)

Making a renovation in the kitchen or in the bathroom, many owners choose the finishing material ceramic or glass tiles. This is a brittle and hard coating. In case of improper handling, chips and cracks appear on it. Therefore, the drill for ceramic tiles must be of a certain type. After all, sometimes it is necessary to make holes in the material, both thin and very large.

For example, in the bathroom, a ceramic tile for hooks under towels is often drilled, and in the kitchen, a place is left in the kitchen for a gas or water pipe. Before work it is necessary to choose the right drill for ceramic tile.

Tool for drills

To select a drill for ceramic tiles, you must first determine the tool. On this depends the correctness of the performance of all work.

To make small holes on the glass or ceramic tile, you will need a thin drill and a hand drill. With this tool you can control the force of pressing and the speed of rotation.

The drill for ceramic tiles is also used in electric drills and screwdrivers, which have a smooth motion function. The tool must not have sudden jerks or vibrations during operation.

Do not use a perforator or impact drill with a drill for ceramic tiles and glass. They will split the material. They can be used only after a full boring of the coating, when it is required to make a hole in the base of the wall.

Professional drills

Drills for ceramic tiles, the photos of which are presented below, have one distinctive feature. Their tip is harder than glass or tile. There are professional drills and tools used at home.

If you use them often, you should purchase a diamond-cutter. It is considered the most expensive. But in the work of a drill for drilling ceramic tiles with diamond dusting the most effective.

A professional repairman, using such a tool in his activity, will quickly pay for the cutter. But at home, such equipment is considered unprofitable.

Cutter for household use

In the event that it is necessary to drill several holes yourself, it will be expensive to purchase a diamond drill for home use. Therefore, manufacturers produce cheaper equipment, designed exclusively for infrequent use.

Their top has a winning tip. The hardness of this cutter is enough to make a hole of various diameters in the tile. However, work with the use of such a drill is longer.

Actions need to be performed carefully. Also today, manufacturers are presented and other types of drills. Their tip is not made of a winner, but of other superalloy alloys. Therefore, when buying a milling cutter for tile, you should pay attention to the purpose of the tool.

Drill for large diameter holes

In order to determine which drill to drill a ceramic tile, it is necessary to take into account the diameter of the hole. Sometimes in a tile it is required to make a place for an outlet, a mixer or a pipe. In this case, a cutter of a certain kind is required. It is usually called a crown.

This is a tubular drill, which has diamond spraying. It also has different sizes. A set of crowns will be quite expensive. It is advantageous to purchase professional repairmen.

However, this tool is able to provide the best result of work. The time of actions is reduced, and the efforts of the master become minimal.

Using a tubular drill, you can make holes in the tile up to 15 cm in diameter.

This type of cutter should not overheat. Therefore, it should be lowered into the water more often. A drill or a screwdriver must operate at minimum speed.

How to apply a diamond crown

Drills for glass and ceramic tiles by the type of crowns require proper operation. This method is suitable for tiles that have not yet been glued to the base.

Before you start, you need to make a note of where the future hole will be located. Drilling is carried out from the front of the tile. In this case, the drill should not be strongly pressed.

If the diamond crown is new and sharp, without great effort, the tile can be drilled in 2-5 minutes.

Also remember that this type of drill does not tolerate overheating. Otherwise, it will quickly become blunt and wear out. Therefore, work with his participation is carried out at low speed, and the milling cutter periodically cools (plunges into the water).

Tungsten crown with centering drill

If the tile is already laid on the base, then drill a large diameter hole in it is very problematic. For this, a cutter is used, such as a tungsten crown with a centering drill.

The work must be done very carefully. After all, a ceramic tile drill, used incorrectly, can cause replacement of the whole block of coating.

When using a tungsten crown, you can get an excellent result, even if the coating is already mounted.

To prevent the milling cutter from sliding over the surface of the tile, use a template with a suitable diameter. He is pressed against the wall. Then the drill with the crown is pressed against the wall and the drilling process takes place. In the case of already laid tiles, the master has to act very carefully, so as not to damage the masonry.

Drill "ballerinka"

If you want to make a hole of non-standard sizes, builders often use a drill for ceramic tile "ballerinka". Its cost will be less than a tungsten or diamond crown. But with the help of such a cutter, it is possible to work even on the surface of the already installed coating.

A drill for ceramic tiles called "balerinka" in form resembles a pair of compasses. Therefore, the diameter of the hole can be adjusted.

Such a drill on the ceramic tile, the photo of which is presented below, has a cutter made of strong alloys. The cutter in the middle serves to determine the alignment.

The disadvantage of this equipment is the complexity of its retention when creating holes of large diameter.

Drilling for dowels

The holes for the dowel need to be drilled, most likely, on the already installed cover. Such work is done if necessary to hang a shelf, mirror, hooks for towels, a lamp and other accessories.

For drilling holes under the dowel, a number of features should be considered. The coating of ceramic tiles is usually quite slippery. Because of this, the milling cutter can move. This will spoil the coverage, and the result of the work will be unsatisfactory.

To prevent this from happening, paint tiles are glued to the tile. This will make the work easier.

Also it is necessary to remember that the drill for concrete is not suitable for tile. To ensure that it does not split, it is necessary to use only special tools. There are recommendations for such work.

Recommendations of experts

To ensure that the drills for ceramic tiles and glass fulfill the task assigned to them in the best way, it is necessary to listen to the advice of specialists in the construction and repair business.

From the edge of the tile you need to retreat a distance of at least 15 mm so that it does not split. Before you start working tile can be soaked in water for an hour. This will also prevent the formation of chips and cracks. It is allowed to simply wet the place of drilling with water.

The safest place to create holes in the already installed coating is the intertitic seams. If possible, dowels should be installed right here. Although this choice of drilling site is not always possible. Therefore, when carrying out work, it is always necessary to adhere to a small speed of the drill rotation, and also do not strongly press on the surface.

If the drilling procedure is incorrect, the coating can be damaged. It happens, when cracking tiles, you have to change several elements of the coating.

Having become acquainted with the recommendations on what should be a drill for ceramic tiles, it will not be difficult to find the necessary equipment. Correctly performing all the actions, even at home and with the installed cover to make the necessary holes in the tile will be able to even a layman. When carrying out the work, it is necessary to take into account the recommendations of professionals on the technology of its implementation.