Balancing stands for tire fitting. Characteristics, prices

Balancing machines (balancing stands) are one of the main devices that are located at the maintenance stations. They are designed to work with the wheels of cars, as well as trucks. At the same time, the balancing process itself can be performed either statically or dynamically.

Disks at the wheels are allowed a variety. Modern balancing stands are able to work with steel, as well as light-alloy models. Use the above equipment only in an enclosed space. It is necessary to monitor the temperature of the environment. As a rule, balancing stands can not be used during frosty hours.

How are the stands arranged?

At the bottom of the stand, the balancing (tire fitting) stand has a built-in ruler that is located above the bed. In this case, the casing with the cells is located above it. Near the display, mounting screws are installed, which are necessary for the processing unit to work. On the side panel of the device there is a shaft cover. Next comes a large shoe that rests against the spring.

On the right side of the equipment there is a set of cones, as well as a quick-release stop. Under the electric motor of the balancing stand there is a brake system. A bolt is provided to fix the wheel, and there is a special pin for alignment. To adjust the position of the shaft, a lifting mechanism is installed.

Important device characteristics

The main characteristics of the balancing stands are the permissible sizes of the width and diameter of the rim. This takes into account the weight of the corrective weight. In addition, manufacturers indicate the error rate in the weight of the wheel. Directly on the balancing affects the angle of correction, which is measured in degrees.

Among other things, attention is paid to the digital indicator's discharge parameter. The permissible weight of the wheel depends on the model of the stand. The time for setting the operating mode can be very different. The quality of the device is also affected by the duration of the measuring cycle, as well as the time of continuous operation. In turn, the power of the consumed network depends on the limiting frequency. The overall dimensions of the device play an important role. Stand balancing (tire fitting) an average of 3500 euros.

Stands of the company "Hoffmann"

The wheel balancing stands of the above brand are distinguished by their high reliability. In many models, the clamp is mounted self-centering, on four cams. Mounting lamp is very mobile. If necessary, its position can easily be changed. Of the shortcomings, only weak fixation mechanisms should be distinguished. At the same time, the speed of the rim must be constantly monitored. In turn, the clamps are fixed with a very high force. In general, the models are quite expensive and not suitable for everyone.

Characteristics of "Hoffman 4500-2"

The diameter of the wheel in this model is a maximum of 25 inches. In this case, the minimum is the ability to install it with a size of 8 inches. The width of the wheel in turn can be fixed no more than 20 inches. The average rotation speed is 200 rpm. In this case, the measurement time is about 7 seconds. The device is powered by a normal 220V network. In terms of dimensions, this balancing booth is average. In assembled form, its weight is 130 kg. He will cost the buyer in the market for about 3800 euros.

The parameters of the stand "Hofmann 3900"

"Hoffmann 3900" is a tire fitting equipment that has compact dimensions. The display is set large, and monitor the main indicators quite comfortably. With manual input, the maximum wheel diameter is 30 inches. In turn, the rim width should be no more than 20 inches. If the wheel weighs more than 80 kg, you can not install it on the stand.

The average speed of the balancing stand is 230 rpm. The working measurement of the deviation parameters takes 6 seconds for the system. Weigh the assembled bench exactly 80 kg. Of the features of this model, convenient programming is possible. In this case, the wheel size input is automatic and does not take much time.

To accurately position the rim manufacturer has developed a special measuring lever, which is connected by a clamping system. A special mode is available for selecting the load position. For one measuring cycle, you can perform both static and dynamic balancing. To increase the maximum stroke, stabilizers are used. The load can be set by the spoke in this model, but in general there are 8 different programs for selecting the wheel position. After measurement, the braking of the rim is automatic. In addition, it is possible to manually stop the shaft with a pedal. The given balancing stand (the market price) costs 5000 euros.

Balancing equipment "Hofmann 6300-2"

The company Hofmann balancing stand 6300-2 power has 0.6 kVA, and the average frequency varies around 50 Hz. The power source of the device is a network with a voltage of 220 V. Continuously work out the balancing stand is capable for 8 hours. In this case, the measuring cycle takes no more than 10 seconds. Among other things, it should be noted that the installation time is good. This occurs when the weight of the load is not more than 200 g for 30 seconds.

The rim width is a maximum of 350 mm, and a minimum of 76 mm can be balanced. The digit of the digital indicator is 1 g, and the mutual correction coefficient fluctuates around 0.1. In turn, the adjustment angle error is 3 degrees. Maximum is the ability to install a wheel with a total weight of not more than 60 kg. The price for this tire fitting equipment is approximately 5500 euros.

Characteristics of the stand AET DST910B

The balancing stand DST910B is equipped with an automatic wheel rotation system. Also from features it is possible to allocate simple input of the basic parameters. A full measurement cycle takes 5 seconds. The accuracy of the data is quite high. The maximum width of the wheel is 20 inches, and its diameter should not be more than 30 inches. The average speed at the balancing stand is 220 rpm. In this case, the rim can be fixed with a total weight of not more than 70 kg. Weigh this model in its assembled form exactly 150 kg. For cones in the system, the manufacturer provides very convenient cells.

Among other things, it should be noted the quality holder of the clamping device, and for cargoes there is a separate lid with cells. The measuring program "Autostop" is installed. In total, there are nine operator profiles in the model. Braking of the rim after operation occurs in automatic mode, and for manual stop there is a pedal at the bottom of the device. You can install cargo for a spoke. To minimize the balancer, there is the "PAX" program.

In general, the rim of the shaft is relatively smooth. Work with the wheels of motorcycles in this model is possible. In this case, alloy wheels are additionally permitted. In one measuring cycle, it is possible to perform static as well as dynamic balancing. This model will cost 6000 euro.

Peculiarities of the "Baysbart" models

In general, many models of stands are suitable for cars, as well as trucks. In this case, the dimensions of the devices can be very different. This is largely due to the diameter of the drive shaft. Additionally, the complexity of the control unit is taken into account. Typically, the balancing stands of the above company are equipped with a 17-inch display. At the same time, there is a pleasant visualization of the process with 3D animation elements.

Among the programs can be distinguished self-calibration, as well as diagnostics. To carry out static, and also dynamic balancing possibility is. Still in many models there is a program for individual adjustment. The cover of the pedestals of the instruments is quite strong. At the same time, it looks very stylish, and in general the design of the balancing stands is well thought out. The models stand on average from 3000 to 5000 euros.

Characteristics "Байсбарт МТ 847"

This model can be serviced by wheels weighing up to 65 kg. The average measurement time is 4 seconds. The distance to the disc is entered automatically. The diameter of the wheel is maximum allowed 30 inches, and the average rotation speed is 205 rpm. The shaft size in this construction is 40 mm.

The standard kit includes the following: a balancing stand (the instruction is attached), calipers, a set of cones, and a laser ruler. In addition, a protective hood and a hammer are applied to remove the weights. The price for this model varies around 3100 euros.

The main parameters of the stand "Baysbart MT 855"

Balancing machines (balancing stands) "Байсбарт МТ 855" speed of control measurements have 4 seconds. In this case, the rims can be mounted on a model weighing not more than 60 kg. The width and diameter of the disk are entered automatically. At that, the working speed of rotation fluctuates around 167 rpm. The diameter of the shaft in this construction is 400 mm. The maximum size of the disc is 30 inches.

The power source of the balancing stand is a network with a voltage of 220 V, and the average frequency of the apparatus is equal to 55 Hz. The accuracy of balancing in this model is pretty good. A set of cones in the standard kit is provided. Also there is a protective casing with a quick-detachable nut. To remove the weights, the manufacturer installed special pliers. The lifting device in the model is pneumatic type. The process of static balancing occurs automatically. In general, the control is quite convenient due to the high-performance microprocessor. The self-calibration mode, as well as diagnostics, starts automatically when the system is started. This model is worth about 3500 euros on the market.

Balancing stand "Baysbart MT 857"

The weight of the correcting load is the balancing stand (cargo) "Baysbart MT 857" has 200 g. The maximum correction angle of the device is 3 degrees. Coefficient of mutual influence is 0.1. Parameter digit of the digital indicator is at the level of 1 g. The maximum width of the wheel is allowed 350 mm, and the rim can be installed with a diameter of not more than 500 mm.

The time for setting the operating mode is quite fast. The duration of the measuring cycle depends on the mass of the wheel. Continuously the unit can be operated for 7 hours. It is possible to feed from the 220 V network, the deviation is allowed at 22 V. The frequency of the power supply network can fluctuate around 51 Hz. The power of this unit is at the level of 0.7 kVA. Dimensions of this model has the following: height 1100 mm, width 1150 mm, and depth - 1000 mm. At the same time, the equipment weighs exactly 200 kg. The price for the balance stand (freight) "Baysbart MT 857" fluctuates around 3200 euros.

Stands of the company "Phoenix"

Balancing devices of this brand are distinguished by high-quality lifting mechanisms. In this case, the wheel is calibrated quite quickly. The entire system is checked every time the device is turned on. In addition, it should be noted acceptable prices for balancing stands, and they are on average around 2500 euros. The frequency of the supply network models is 51 Hz. At the same time, the average voltage is at 220 V.

Dimensions of the balancing stands are very diverse. The measuring cycle usually lasts for 20 seconds, and measurement takes only 10 seconds. The error is rather small. Correct the angle of the wheel is very simple, there are still many modes for balancing.

Model "Phoenix W 920"

The given model has absolutely unique technology of measuring the balance of the rim. You can service trucks. The distance and diameter of the wheel are entered automatically. The measuring lever is equipped with a special clamping system.

Among other things, it should be noted ultrasonic sensor, which quite accurately calibrates the device. The choice of the position of the goods is carried out in automatic mode. Carry out balancing of the wheels from the motorcycles can. There are programs for static measurement of parameters.

The maximum wheel weight is allowed 200 kg, and the diameter of the wheel should not be more than 26 inches. The average speed of rotation fluctuates around 215 rpm. The operating air pressure is maintained at 8 bar. The noise level of this unit is not more than 65 dB, and this equipment is worth about 2,500 euros for balancing on the market.

Characteristics of the stand "Phoenix FW 6606"

This model is equipped with a large LCD display for control. Among other things, you can note a convenient ruler for entering basic parameters. There are eight programs in this balancing booth. Among them, one can distinguish self-diagnostics, as well as qualitative calibration. Protection from dirt in this model by the manufacturer is installed.

The shaft has a diameter of 40 mm, its tail is considerably elongated to increase the torque. The cover of the curbstone is quite strong, and the equipment is standard. In general, this equipment for balancing is universal and suitable for different types of wheels, but it costs 3300 euros on the market.