Awning for boat PVC with own hands: material, accessories, instruction

Many lovers of fishing prefer to use for their hobbies a boat. In this case, every connoisseur of "quiet hunting" wants to spend time with comfort and to protect himself as much as possible from weather conditions. Therefore, questions about how to make a tent for a PVC boat with your own hands, are discussed by fishermen as often as advice on lure or tackle.

Self-made or shop purchase?

To date, modern markets are simply overcrowded with different types and models of awnings, which are designed for a specific type of boat, and can act as universal designs. However, the decisive factor in choosing such products is their price and quality. The fact is that sometimes a good coating can cost not less than the vehicle itself, and cheap models are so impractical that they only bring discomfort. Given this, many fishermen believe that it's best to make a tent for a PVC boat with your own hands. Such a solution allows not only to save a lot, but also makes it possible to get the final product that best meets the requirements and tasks of the user.

Varieties of structures

Before you start making your own, it's very important to first determine the type of product. There are several fundamentally different designs that are made for specific purposes and tasks. Therefore, making a tent for a PVC boat with your own hands, it is worthwhile to study all of them in advance.

Parking

This type of awning can be considered the simplest and inexpensive to manufacture. It is made in the form of a large cover, which is fixed to the elements of the accessories of the boat with a cord. Typically, the design of this type of awning does not take a lot of time and effort, but it should be borne in mind that it will protect the vehicle only during parking at long transitions. However, this allows you to protect from bad weather as well and hand luggage, which is placed in the boat.

Nasal

A standard awning bow for a PVC boat is made in such a way that it covers about a third of the vessel. There are also products that can protect half of the vehicle, but this depends on the individual design. It is believed that it is best to create such an awning on the basis of the frame, but its fixation must be strong enough that the gusts of the wind do not tear it off when driving.

Chodovaya

Such products can be considered one of the most popular. Typical running tents for PVC boats are used both during the movement of the vessel and when it is in anchorage. The main feature of such structures is the ability to open one or more sites, which allows you to fish without removing protection from the sun or rain.

Frame

This stage of work requires a creative approach and a little wit. The fact is that, creating even the most simple running tents for PVC boats, it is very important to correctly calculate the location and fastening for the frame. Most often it depends on the individual design of the boat itself, but if necessary, you can make some changes to it. Using additional fittings. In principle, changing the design of the swimming device itself is not only not recommended, but in some cases even prohibited.

Typically, the frame is made of materials that are not exposed to moisture and corrosion. Aluminum pipes from old clamshells are the best for these purposes, although PVC water pipes can also be used. The design fixing points are selected individually. They are made according to the type of boat used and the available fittings.

Immediately it is worth noting that the bow for the boat PVC must be fixed fairly firmly and not have any weakened seats or strong gradients. Therefore very often such constructions are made in the form of independent products with the possibility of their installation on a swimming device.

Selection of coating material

Usually, the manufacture of awnings is made of a special moisture-repellent fabric. However, the cost of such a material of appropriate quality is quite high and will lead to too much expenditure. Given this, most masters use PVC. At the same time, they create opening sections, since such fabrics completely do not allow air to pass through. Professional fishermen are advised to make a combined awning. They offer to install transparent parts of PVC on the nose, and the rest of the cover is made of a fabric that "breathes" and does not let sunlight pass.

Additional materials

As an additional material usually serves accessories for awnings and boats. Their choice directly depends on the swimming device itself and the type of coating produced. However, it must be remembered that when working, you will almost always need rings to fasten the rope. Usually they are called eyelets, and they serve for the installation of tissue in the places where the hole is created.

For the production of strong seams, glue can be used. It is selected on the basis of the coating material and compatibility with each other. Also, when sewing awnings, special patches made of durable fabric may be required, which are usually installed where the material will be permanently or permanently mechanically affected.

When making doors, opening beads or flaps, you may need buttons, locks or even additional eyelets to install the strings. In this case, each master decides which material to use, depending on the design and personal considerations of practicality and convenience.

Sewing

• It is believed that the manufacture of awnings is a fairly simple matter. However, when it comes to practical work, a lot of difficulties arise. They are associated with inconsistency in dimensions, errors in the pattern and other errors, which are not so noticeable in the preliminary stages. Given this, experts advise first to make a draft version of the design, which is sewn from cheap material or old rags.
• The draft version is installed on the boat and begins to fit directly on the product. In this case, it is very important to immediately note the places of installation of eyelets, patches, pockets for the frame and other elements.
• At this stage, the frame is assembled and the dimensions of its parts are regulated. If a tent-transformer is made, its adjustment is carried out in all positions, beginning with the installation variant, which assumes the maximum coverage of the boat.
• Next, the finished product is cut into patterns for which the selected material is to be cut. At the moment, it is necessary to take into account a small allowance necessary for the manufacture of seams and outer edges.
• Then, all joints are glued and the finished awning assembled. This is necessary not only to make the seams more durable and able to withstand moisture, but also in order to facilitate the tailoring itself.
• Typically, the accessories for the tents are installed at this stage, and during its installation, glue may also be required.
• Final sewing is performed with a special machine or manually. However, it must be remembered that the mechanically created stitches are more practical and will last much longer. Also, the use of special equipment will greatly facilitate the process itself.
• After the material is sewn, it is pulled on the frame, leaving it so for the night. So you can check the strength of all the seams and give the product the necessary shape. Some masters suggest at this point to treat the tent with a special compound that repels moisture, but if the coating is chosen correctly, then this procedure will be superfluous.

Recommendations of specialists

• If a shipping canopy is made for a PVC boat, it is not necessary to create a rough cover version. It is enough just to pull the chosen material and perform the installation of the eyelets. The firmware of the edging can be made later, when the pruning is done to the required size.
• Some wizards recommend installing snakes on the material to create connections that can be opened if necessary. However, professional fishermen prefer special ties or buttons. This is more practical and when the mechanism fails, it can be repaired in a short time without leaving the boat.
• Sometimes it is much easier to attract a specialist to this work, which will produce the entire tailoring. However, such masters may require ready-made patterns, as they do not want to be responsible for the discrepancy in size.
• If the canopy is intended for an inflatable boat, then it should be dismounted and able to occupy the minimum space when laid. The cover itself is usually folded quite simply, which means that you will have to pay particular attention to the racks. They should not only be quickly and easily disassembled, but also compactly packed.
• If there is already a finished product that perfectly meets all the necessary requirements, then you can create your own patterns based on which, and the pattern will be made.
• Recently, small tourist tents began to appear in sporting goods stores or markets , which have a low cost. The very design of such products is not always practical or quality, but to create a small tent such a tent is quite suitable. Racks and elements of creating an entrance are especially good at work.
• If you need an awning that will only be used in permanent parking areas, even a tarpaulin can be used to make it. Lighter materials are suitable for products that will be used in the marching state or while driving. This will help to save money.

Conclusion

To make an awning for a PVC boat with your own hands is quite simple. It is enough to have a clear idea of what kind of this product you need to get, and decide on its fixation on the ship. The creation process itself is not very complicated, and even a novice master who has a common understanding of the work and the tool necessary for this can master it. The most important thing is to correctly determine the material of manufacture and choose the appropriate accessories.