Replacing bulbs for vehicle number lighting

In order to change the light bulb numbers on the car, you need to remember some of the rules. First of all, you can install by yourself only the illumination of the license plate, which is located behind. For this purpose it is recommended to use LEDs with lenses, since they better illuminate the number and, according to the law, enable more clearly to see the number plate. Although there are lamps of various colors in free sale, the law does not allow many of them to be used in practice.

Independent work for drivers

Replacement bulbs for highlighting the number are as follows:

1. With a thin screwdriver, it is necessary to disassemble the plafond in half, starting from the middle.
2. Carefully unscrew the standard lamps, as it is quite easy to damage the holder on the body.
3. The next step is to install LED or incandescent lamps.
4. Before installing the plafond in its place, degrease.
5. After installing the lamp, you should check the operation, if the replacement of the backlight indicator light has been performed accurately, the number will be brightly lit.

When replacing the backlight on different models of cars, there are small nuances that differ when installed. That the work was done correctly, it is necessary to take into account such differences.

Work with "Hyundai-Solaris"

The license plate is illuminated by two lanterns, which are located on the boot lid under the lining, they are interconnected. In order for the replacement of the "Hyundai-Solaris" light bulb, it is necessary to remove the trim from the trunk lid, for this:

1. Fit the screwdriver cover in the handle, which closes the trunk.
2. Despite the resistance provided by the latches, open the lid.
3. Using a Phillips screwdriver, unscrew both screws that secure the handle, remove it.
4. Using the same screwdriver, unscrew the pistons that attach the upholstery in the trunk lid and remove them, after which the padding is removed.
5. It is necessary to rotate the cartridge clockwise until it stops and, together with the lamp, take it out of the lamp housing, the wires must be pulled out so long that it is convenient to change the lamp.
6. To remove the lamp from the cartridge, it is enough to pull it by the flask.

To replace the backlight bulb of the Hyundai-Solaris number correctly, the entire installation of lamps and parts must be done in the reverse order.

After the completion it is necessary to check the assembled equipment. If all conditions and requirements are met, the backlight should work smoothly, only after that the replacement of the lighting lamps of the "Solaris" number will be considered qualitatively.

Substitution on "Prior"

Doing this kind of work on the "Prior" is also not difficult, it's enough to follow the instructions and have the necessary tool. First of all, you will need the end keys:

• With the keys you need to remove the plastic, which is attached to eight hedgehogs.
• To remove the rear chrome frame above the number, unscrew all four nuts. Lamps are installed in the frame.
• In order to get the bulbs installed in the plafond, you need to apply a little effort, as they are difficult to disassemble.
• When opening the cover, it is important not to lose the sealing gum. The replacement of the lighting lamps of the "Priora" number is done quickly.

It is necessary to check the operation of the installed light bulbs before assembly so that they do not have to work again. The process of reverse assembly takes place in the exact order with its disassembly. After replacing the lamps, plafonds are installed, then a frame is placed in its place, which is fixed with bolts. After that, the plastic is removed. This is the replacement of the light bulbs of the number is considered finished.

The replacement process at "Kalina"

Over time, any car is required to replace worn out parts, is no exception and "Kalina". If the license plate has become poor or unevenly illuminated, the lamp of the backlight of the "Kalina" number is being replaced. It's easy to do it yourself:

1. For greater convenience, it is necessary to open the trunk of the car, remove the lampshade.
2. To remove the plafond with a thin screwdriver, press on it from the left side until it moves to the right and squeeze it.
3. Carefully, not to break, lifting the latch up, using a screwdriver, you need to remove the flashlight.
4. Lift the plastic lock up and remove the power plug.
5. After this, take out the base with the bulb, turning the white body counterclockwise.
6. We remove the bulb from the cap, lightly pulling it to the side.
7. After replacing the lamp, all work is done in the reverse order.

Replacing bulbs for backlighting the room does not require special skills, attention, patience and the desire to produce it yourself. Many owners of "Kalina" often face this problem, its solution does not take much time and does not require the intervention of specialists.

Backlighting of the issue on "Kashkay"

The replacement of the backlight lamps of the "Kashkay" number does not differ much from this procedure in other cars, there are only small nuances that should be adhered to. First of all, before repair, you need to disconnect the negative cable from the battery. Then you need to do the following:

1. Use a screwdriver to remove the rear lights of the rear license plate. To do this, you need to gently push it to the right and pull it out.
2. Carefully remove the cover of the plafond.
3. Disconnect the connector.
4. To pull out the lamp, it is necessary to turn the cartridge counterclockwise.

After a simple procedure, a new light bulb is inserted and the assembly is carried out in the reverse order. After installing the minus cable in place, you need to check the operation of the highlight of the number. Replacing bulbs for highlighting the number with your own hands will save you not only time, but also money.

Self-repair on the "Renault Logan"

Backlight illumination is needed at night to determine the registration number of the vehicle. Therefore, when it breaks, you need to replace the backlight bulbs, which you can easily produce on your own. For "Renault Logan", as for many other car models, incandescent bulbs and LED bulbs will suit. The former do not have high reliability and low energy consumption, but due to the low price they are in demand. The latter have great brightness and use little energy, but their cost is much higher.

Replacing the bulb lights room on the "Renault Logan" does not take long:

1. It is necessary to disconnect the negative cable from the battery terminal.
2. Press the catch and remove the license plate light from the rear bumper groove.
3. Press off the lock and remove the diffuser of the lantern.
4. Remove from the lamp a lamp that does not have a socle.
5. Install the new lamp and assemble all the parts in the reverse order.

Self-installation does not take much time and will quickly fix the breakdown.

Backlight on "Toyota Corolla"

If you need to replace the backlight backlight on the car "Corolla" you need to perform simple actions.

1. Push the tongue and lower the diffuser of the flashlight down to get easy access to the corrupted light bulb.
2. Then turn the bulb holder counterclockwise, then remove it.
3. Then unscrew the screws on which the license plate lamp is fixed and lower the lantern completely.
4. Then remove the lamp holder by turning it counter-clockwise.
5. The last action is to get the bulb from the cartridge.

When the "Corolla" light is replaced, the assembly is in the reverse order. Such work can be done by each driver independently.

Backlight for back number

By the rules of the road at dusk, the rear number plate should be highlighted with a yellowish or white light. This will not only help determine the vehicle number if necessary, but also shows its direction of travel. If the license plate is lit in blue or red or bright LEDs, this could trigger an emergency situation. Since at night, the perception of the driver moving behind can vary.

Work for professionals

Not all drivers, faced with the problem of the burned bulb on the backlight, try to do the work themselves. Sometimes an obstacle may be the need to remove the casing inside the trunk or remove the plastic rivets - many are afraid to break them. It is not always possible to remove the plafond, or rather short wires are found and it is almost impossible to reach the bulb. In such cases it is better to turn to professionals.