Repair of the washing machine "Zanussi" with their own hands. Self-repair of washing machine Zanussi

All faults are divided into rare and typical. In 90% of cases they do not cause special difficulties and many masters carry out repairs of the washing machine "Zanussi" with their own hands. A qualified specialist can identify and eliminate complex breakdowns caused by the actions of the owner, manufacturer or installer. Typical faults that caused malfunction of the unit and require the intervention of the user or the master are discussed in this section.

Drum does not move

Users of branded equipment often have to deal with a problem when, when loading parameters, there is no rotation of the drum. Such troubles can be explained by the failure of the belt or motor.

If the consumer does not rush to call a specialist and decided to repair the washing machine "Zanussi" with his own hands, it is required to check the free running of the drum's torque by rotating it in different directions. In the absence of third-party sounds, belt tension is checked. The process consists in removing the side panel of the device. While maintaining the integrity of the belt and quality stretch, it is necessary to check the rotation of the motor pulley. In the presence of breakages at this stage it is better to call the master.

Lock hatch

After the successful loading of linen, the imported apparatus often refuses to return it to the user. Problems with the jammed hatch are caused by the blocker to be replaced. If you need to urgently get the laundry, you can repair the washing machines yourself or entrust the work to the master.

• It is necessary to remove the bottom plastic panel and to find in the right bottom corner, near the filter a cable of bright red color for emergency opening of the device. It is enough to put it on yourself and open the locked hatch.
• In the absence of a cable, the upper panel is removed and the locking device breaks.

At the subsequent start-up, the washing machine "Zanussi" must be closed with a hatch on the latch - the door will unconsciously open during operation. Ignoring this item will cause more complicated repairs.

Self-draining apparatus

If, when the device is turned on, it picks up water and immediately releases it, before the washing begins, the cause is incorrect installation and connection of the device, defective spout connections.

The preliminary check consists in raising the drain hose to the level of 50-70 cm and turning on the washing mode. In the absence of normal operation, replace the pump or check the electronic module. A more accurate reason will be installed by the repairman of washing machines, arriving at a call with professional equipment for diagnosis.

Do not dial water

The lack of recruitment or the slow arrival is caused by prolonged exploitation or weak pressure in the water supply. The occurrence of the problem is influenced by a low level of fluid intake from the central highway or slow delivery.

Check the presence of pressure in the water supply and the position of the valve (open / closed). The filtration system may be clogged. For cleaning, it is necessary to remove the supply nozzle (from the back of the device) and remove the mesh from the pliers.

In the presence of contamination, the filter is washed under running water and installed into place. If the repair of the washing machine "Zanussi" with your own hands did not yield results, you should use the services of a specialized service. Possible damage to the fill valve or lack of power. Additionally, the water level sensor or the modular system is checked.

Rapid turns

A similar problem has the characteristic features: a number of smooth rotations of the tank are made and the revolutions are gaining momentum. In some cases, the device vibrates violently with increasing drum speed. The fault lies in the collector motor or power circuit. Separately, problems with the module are considered. It is possible to untwist the magnet or oxidize the contact. If you have experience in the service of imported units, you can try to repair the washing machine "Zanussi" with your own hands. In case of doubt, it is recommended to contact the professionals.

No water heating

If the heater is burnt out, the installation of a new product is performed only if its power is similar. To remove the failed TEN, the side panel is removed and the bottom of the tank is inspected. Particular attention is paid to the flange. When unscrewing the nut, it is not recommended to remove it. It is necessary to press down the fasteners so that they fit tightly into the flange with the bolt. Having loosened the fastener, it is possible to remove the heater. At this stage it is not recommended to make sharp jerks, it can damage plastic parts.

If the heater is in working order, the cause of the unit's malfunction may be caused by a faulty thermostat or heater relay contacts. If there are difficulties with determining the breakdown, further actions usually involve contacting professional service professionals. The master of repair of washing machines will carry out the work at the place where the equipment is used.

Puddle formation

Typical breakages include the occurrence of problems with basic details.

1. Breakage of the branch pipe.
2. Formation of cracks in the hatch cuffs.
3. Low-quality gasket of the delivery branch pipe.
4. Drum leak.

Replacement of the delivery nipple is done by yourself. And for other types of repair, you should contact the master.

Error Codes

Е11 - no water supply during operation. An error is possible if within 10 min. The amount of water in the tank does not reach the specified mark. The fault usually occurs in the water supply tap. With the necessary tools, knowledge and experience, users can easily repair their own washing machines. It is required to check the water pressure, the integrity of the tubes and the absence of clogs in the grid. The resistance of the valve coil is measured (the optimum parameter is 3.8 kΩ).

E12 - a problem with water intake during drying. If the water intake valve fails, the code is knocked out after 10 minutes. Operation.

E21 - no draining. It is required to clean the filter and check for contaminants in the nozzles. It is necessary to check the operation of the impeller of the drain pump. If there is no free wheeling, you will need to replace it.

E22 - insufficient level of draining of water in the drying mode. It is necessary to clean the condenser.

Screening during spinning

If the machine rattles when washing or squeezing, it is necessary to suspend operation and check the source of noise. If the stroke is difficult, find the cause in the bearing.

If the Zanussi washing machine is out of order, the instructions for self-replacement of bearings will save money and gain experience in servicing imported equipment. The technology below is ideal for servicing the Electrolux equipment. Main stages:

• The side panels are removed. To do this, unscrew the screws located on the rear wall of the device.
• The bearings are changed from the side where there is no pulley. Loosen the screw on the drum axis. On the support of the tank are marked 2 arrows: Close and Open, they indicate the direction of the torque for screwing or unscrewing the caliper. Left and right sides are placed on opposite sides.
• The bearing of the Zanussi washing machine is replaced by a puller. The supporting unit is equipped with a right-hand thread and unscrewed in the opposite direction. After removing it, it is necessary to clean the packing area of the stuffing box and the drum shaft from contamination.
• Depending on the spin speed, the machine is equipped with the Cod.098 (099) parts with the 6203 unit and the VRING VA22 rubber (when spinning to 1000 rpm). When marking Cod.061 (062), it is required to replace the supports of the rotating parts under number 6204 and the gland 30x46,8x8,7 / 13 (with a spin of 1000 rpm).

• Before placing the purchased support, you should grease the oil seal. This will be the lubricant offered in the seal set.
• After placing a new part, scroll it to the Close direction.

Regardless of the type of machine, whether it's the Electrolux technique or the Zanussi washing machine, the instructions for reassembling the parts require paying special attention to the seal. The presence of distortions is excluded, because this will cause a decrease in the tightness of the container. When tightening the unit, it is not recommended to exert great efforts. The thread is plastic, and the calipers have self-extinguishing properties.

Pulley assembly change from pulley

Stages of work:

• The drive belt is removed.
• Unscrew the screw and remove the pulley.
• The grounding plate is disconnected.
• The support is unscrewed (to the right).
• Has some features of the operation of "Zanussi" (washing machine). Vertical loading of the machine requires regular cleaning of the stuffing box and the drum shaft.
• Omentum smears.
• Mount a new support, twist it in the direction of Close.
• Grounding is applied and a pulley fixed with a screw connection. For the maximum level of thread fixing, use Loctite glue.
• The drum drive belt is installed.
• The side panels are reset.

Inaccurate handling of the machine will cause further malfunctions of the Zanussi washing machine. If all the work is done correctly, it remains to check the device in operation. The first start after fixing is done without linen - for washing the product.