Cupboard for the aquarium with your own hands: photo and drawing

The presence of an aquarium in the house has a beneficial effect on the well-being and mood of each member of the family. A person underwater world always caused strong impressions, and if you create an artificial aquasphere in the apartment, then the room will differ in unusual design. You too can follow this example without spending extra money on expensive furniture for equipment.

Unique shells, mysterious caves and drowned in the sand amphora fascinate anyone. If you, too, decided to become the owner of such beauty, then the aquarium should not be installed on the chest of drawers, because a strong and waterproof pedestal made by oneself will be the best solution. If we are talking about the usual capacity, where only a few fish are placed, it can be installed on any flat surface, previously protected with "Isolator".

Why do we need a special curbstone

If the capacity of the tank is 50 liters or more, then a flimsy table for this does not work, you need a strong stand. In addition to a heavy aquarium, whose walls have a thickness in the range of 8 to 10 mm, the countertop will be affected by water, soil, decorative elements and technical devices. If a deflection occurs at least one millimeter, a crack may appear in the bottom glass, which will subsequently cause trouble. Therefore, the issue of the cabinet should be taken with all seriousness.

Preparatory stage

If you will be made a pedestal for an aquarium with your own hands, then the glass container is better to fit into the dimensions of the structure. However, if the aquarium is already available, then the dimensions of the stand should be better adjusted to it. Its basic dimensions are equal to 1060 x 1000 x 450 mm. The future design will look like a cabinet with two doors and an upper folding box, which will be used for lighting. It is to be fixed to the side high walls.

Material preparation

To carry out the work, it is necessary to prepare a carpenter's plate. It is recommended to use laminated chipboard or MDF. It is important to take into account that the water from the artificial reservoir will fall on the curb, because you have to catch fish during spawning and add water. If it is a non-laminated surface, then it quickly deforms. This will cause cracks in the aquarium. Therefore, the ends, nests with screws and conjugation of parts must be covered with several layers of varnish.

Preparation of tools

If an aquarium cabinet is made by hand, then you will need some tools, among which:

• Circular Saw;
• drill;
• clamp;
• Milling machine.

The saw blade should be fixed on a workbench. As for the drill, it will be needed to prepare holes for the dowels. You can also come in handy and screwdriver.

Preparation of fittings and workpieces

The aquarium stand with its own hands, the drawings of which are presented in the article, should be made from a carpenter's plate, it should be presented in two varieties, one of them will have a thickness equal to 18 mm, while the other - 38 mm.

The first type of material will be used for the manufacture of shelves and walls, the second one will be needed to carry the load-bearing elements. Take care of availability:

• A piano loop;
• Joinery glue;
• Wooden dowels;
• Handles;
• Furniture varnish.

The latter can be replaced with decorative wax.

Additional recommendations

When buying pens, you must remember that their installation will be carried out on the door. You will need screws and screws. With the help of a circular saw you can cut out all the details. This tool will help prepare grooves and form ridges, the latter of which are needed to interface parts. The main load will fall on the side walls, for them a 38-mm shield should be used.

Assembly of the curbstone

When doing a thumbs-up for an aquarium with your own hands, it's better to enlist help, because some blanks have to be connected simultaneously, working on weight. At the first stage, you should prepare ridges and grooves for the wall. They will be located in the bottom, sidewalls and the middle lid. Such elements will also be in the blanks of the upper box.

Instead of a circular saw, a milling machine is sometimes used. The next step is to glue the parts of the back wall and the upper corner. The latter will be located behind the module for backlighting. Straps are tightened together by clamps and left until the time of drying. When a pedestal is made for the aquarium with their own hands, the next step is to screw the socle 38 mm bars to the bottom shelf, which will serve as the bottom. It is on them that the entire structure will be installed.

The inner sides should be screwed with 18 mm plates to install the middle cover. The leading edges must be flush with the edges of the bottom shelf. The rear will be located at the level of the inner edge of the groove. The middle lid and bottom should be glued together with the central inner partition. According to the design features, the described chest should have a vertical partition for every 30 cm table top. If you do this in this way, you can save the given geometry.

The lower part of the rear wall must be inserted into the bottom groove. One side is fixed to the middle cover and the bottom with dowels, they should be placed on the glue, directing the rear wall into the groove of the side wall. The corner is attached to the top of the sidewall, it needs to be done in the same way, using glue and dowels. It is on the corner and will rely on the upper module. All these manipulations must be repeated using the second side wall.

Methods of work

A pedestal under the aquarium, with their own hands (photo presented in the article) made, must have an upper box, its assembly is carried out at the next stage. It is there that the reinforcement for the lighting is installed. The bottom of the box, which will be turned to the water, will look like a sheet of frosted glass, it is installed in the grooves of the longitudinal sides.

The assembled module must be fixed to the curbstone , using a piano loop, if necessary, it can be folded. From the carpentry board, you need to cut out the doors, the dimensions of each of which are 433 x 494 mm. On the template, you need to mark out the sockets for setting the loops to select them with a drill. The doors are installed to the side walls using hinges with hinges.

To supply air, you need to install a compressor in the cradle. Here is the control panel for the backlight. Tubes and cables must be withdrawn through a groove, the dimensions of which are 25 x 50 mm. Place it in the lid. The assembled stand must be covered with furniture varnish, which is applied in several layers. On this we can assume that the curbstone for the aquarium with their own hands, the drawings, the photo of which is presented in the article, is made by you.

Manufacturing of a corner pedestal for an aquarium on 150 or 200 l

To simplify the work on the cabinet, you can purchase finished chipboard panels that have laminated edges. It is especially important before starting work to determine the additional components that will be placed inside the piece of furniture. This can be a water filter that is installed outside.

To work, you need 4 panels with dimensions equal to 16 x 300 x 800 mm, two panels should have dimensions of 16 x 268 x 284 mm, one panel will have dimensions of 16 x 316 x 300 mm, another - 16 x 800 x 800 mm. For technical elements, electricity must be supplied to the installation site of the pedestal. At the first stage, the side panels are joined with dimensions of 16 x 300 x 800 mm. Do this work is necessary with the help of self-tapping screws 3.8 x 55 mm. Sometimes screws-confirmats are used, for which it is necessary to prepare holes first.

When the corner cupboard is placed under the aquarium by one's own hands, in the next step it is possible to connect the resulting structure to the top shelf, for this the same technology is used. The next step is to install the bottom, the hardware remains the same. The last ones are the doors, then the legs come next. On the sidewalls, the support angles should be strengthened, they must be made from the slices from the countertop. On the upper joint, self-tapping screws with dimensions of 3.8 x 55 mm should be used, with regard to the lower joint, the fastener dimensions are reduced to 3.8 x 42 mm. Fasteners should not be installed too low.

Algorithm of actions

A pedestal for an aquarium of 200 liters is made by its own technology. When designing it is necessary to use a template, it will look like a piece of cardboard, which you need to fit into the dimensions of the panel. Once the sections have been made, it is possible to paste the edge by treating the edges with silicone.

The worktop is mounted on the body and connected by screws. If you make a pedestal for an aquarium of 150 liters with your own hands, you should not forget to make cutouts in the remaining panels for furniture loops. For this, a milling cutter is used. By the same principle holes for the handles are prepared.

Next, the cabinet can be installed in a corner, placing the aquarium on the table top. Preliminary design is leveled using the legs on the level. On the wall, it is necessary to note the bottom edge of the structure to install on both sides of the wall iron corners. They are necessary in order that the curbstone for an aquarium of 100 liters with their own hands was bolted to the base. If necessary, you can embed the furniture lock, and then install the shelf. It will be represented by a panel with dimensions equal to 16 x 268 x 284 mm. Inside the cabinet, shelf holders are installed, which should be located at the height that the equipment requires.

Conclusion

When choosing the height of the pedestal, you should take into account that the person in the sitting position should be comfortable to consider the contents of the aquarium. It is important to provide the structure with adjustable feet, with which it will be possible to change the height in the range from 50 to 100 mm.

Before you make a tank for an aquarium with your own hands, you must determine also the depth of the future artificial pond. This will make the cabinet with a width that is equal to or slightly larger than the mentioned parameter. It will be safe and beautiful. Do not neglect internal vertical partitions. If the depth of the aquarium is 50 cm, then usually a chipboard thickness of 22 mm or more is used.