Brazier from a car disk: manufacturing

Means for frying meat can, of course, be purchased at stores of the corresponding goods. However, such structures are quite expensive, in addition, sometimes they are completely unsuitable for certain conditions due to excessively large or small dimensions. Alternatively, an approach may be proposed that involves the manufacture of such a device on its own. A brazier can be made from a car disk.

Preparation for work

To make a brazier you need to stock up two car disks, nuts and large bolts in the amount of 3 pieces, and also an 8 mm wire, the length of which is equal to one meter. A rectangular pipe (one meter), as well as 10 mm nuts in a quantity of 4 pieces, will be needed. It is important to worry about the presence of a welding machine, electrodes, grinders, as well as masks and welding gloves that are needed for individual protection.

Recommendations for material selection

If you decide to make a brazier from a car disc, then the accessories are most preferable to borrow from the old domestic car of the type "Lada". The main condition for this is solid steel, not aluminum alloy. Today it is not difficult to find such blanks, it is easiest to do it on tire service, where you can give the disks completely free of charge or for a small price. If this approach is unacceptable, then the disks can be purchased through the online store. The elements that were in use are very small. The remaining components such as pipes, bolts, wires and nuts can be purchased at any construction shop.

Open discs

If you make a brazier from a car disc, it is important to think about how the cutting will be done. Initially, it is necessary to prepare the holes for the bolts, this is easy enough to do by grinding. Cutting should be done near the factory holes, doing this in such a way as to save the maximum amount of time and effort. Cut off parts should be discarded, since the brazier will do without them. Now the wizard must remove the partition, the easiest way to do this is with a gas cutter. If there is only a Bulgarian, then initially it is necessary to make an incision, the length of which is 2 cm, moving from the spot weld made in the plant conditions. After the partition has been removed, there will remain surplus, from which it will be possible to get rid with a screwdriver or a hammer. This will get a fairly accurate rim, which is devoid of septums.

Welding works

Making a brazier from a car disk, at the next stage it is necessary to carry out welding works. Disks are installed in such a way that a single brazier is produced. An untouched disk with a partition should be installed downward, while the partition will serve as a bottom. The second disk, which is already devoid of the partition, must be installed from above. Before carrying out welding, alignment should be carried out, now the disks can be welded around the perimeter.

In order to execute the door, two vertically oriented incisions should be made so that the weld seam is located in the central part of the future door. In the lower part of it you should leave a strip, the height of which is 4 cm. It will act as a threshold, so that the coals do not fall out. If you make a brazier from car disks yourself, then, once the door is completed, you should make a loop. To do this, use nuts and bolts. The first are wound on the last and welded to the brazier.

On this you can assume that the door is ready, it remains only to process the edges with a file to remove the "burrs." The next step is to weld the handle. To do this, a hole is made in the door, into which a large bolt is screwed and welded.

Mounting of carrying handles

If you make a brazier from car disks, the photo should be considered even before the start of work. In order to use the design was more comfortable, you need to provide it with handles. To do this, use 8- or 10-millimeter wire. Vices and a hammer will allow to bend a workpiece in the form of handles. The ends of the wire are put on the nuts and welded to the body.

Recommendation of the master

In order to exclude the gripping of the handles to the brazier and their heating, the ends of the wire must be bent 90 degrees. This will allow the handle to be positioned so that it rests against the body.

Making the legs

If you need a brazier from a car disk, how to make such a design is described in the article. Now you can proceed to the legs, for the manufacture of which you need a rectangular pipe. It is cut into three parts, each of which has a length of 40 cm. At the bottom of the disk there are factory holes on the partition, they facilitate the manipulation of welding and can save time on marking the points under the legs. These elements are welded to the holes of the disk.

Conclusion

On this, we can assume that the brazier from the car disk, the instruction for manufacturing of which is presented in the article, is ready. The device is compact enough that it can be transported even in the trunk of the car, which can not be said for factory models that can have large dimensions.