We make by hand the pattern of the sleeve-flashlight

On the question of what kind of outfit is the most favorite among women, almost everyone will answer unequivocally: "Dress!" The story of his appearance in the wardrobe is rooted in the beginning of the emergence of human communities. Style, cut, design constantly change from one century to another. One is invariably in this amazing outfit - he always emphasizes female beauty, grace and makes a woman even more tender and irresistible. Each dress is beautiful in its own way, but it is especially elegant if the sleeve is cut out with a "flashlight", that is, it is somewhat prisoboren or draped over the shoulder or on the cuff. The pattern of a flashlight sleeve can be made by any woman. You just need to take the foundation of the drawing and simulate the assembly.

We make a pattern of a sleeve-flashlight

If a decision is made to sew a romantic dress, in most cases it is planned to assemble on the sleeve. The dress pattern with a "flashlight" sleeve is made very easily, if there is a base of the drawing. There are several types of this dress. Hose-lanterns can be different. Assembly can be done on the casing and bottom. To obtain this type, you will need to take a drawing of the pattern of a short sleeve. There are three vertical lines on it, where one should be centered (that is, by the elbow fold), and the second two - on the sides (one on the shoulder notch and the other on the other side), and it is important that the distance between them is the same . Then the drawing along these lines is cut and expanded to the required width (this will depend on the proposed assembly).

Assemblage at the bottom of the sleeve

Again, the base of the dress or shirt is needed. The pattern of a blouse with a "flashlight" sleeve is built according to the above method. Only in this case the assembly will be mainly on the bottom and, perhaps, slightly - on the pellet. Three lines are also applied: on the elbow, on the shoulder incision. Only in this case, the drawing will need to be expanded only at the bottom. That is, the upper points on the lines are left in the initial position, and the lower ones are moved to the desired width. The resulting pattern of the flashlight sleeve will only be left on paper or fabric. The bottom of such a sleeve is usually processed from below by a cuff.

Sleeve-flashlight long

Romantic blouses and dresses can be for any time of the year. And if there is a basic pattern of the sleeve "flashlight" (long or short it is not important), then it can always be modeled. Just take the base of the dress with a long sleeve. And the assembly can be scheduled both on the pellet and on the bottom, and it is quite possible in two places at the same time. It depends on the woman's desire. The principle of modeling is the same as in the first two cases. Three lines are planned and traced, and then depending on the location of the assembly they are moved apart in the drawing.

Unusual sleeves

In the fashion world, what is not created. Today, the same flashlight sleeve can be seen not just priborenny in the usual way, but with folds. This is a somewhat complex model, but if you want, you can also master it. The pattern of the flashlight sleeve can be made exquisite. The basis of the drawing is taken. We must immediately determine the length, draw a line and cut off the excess. Then future folds are planned. From the point of the elbow bend (that is, the center), two points should be noted at the same distance in both directions. Further from the ulnar point to draw a line downwards (this line will not be cut, it is necessary for the construction of folds). Then, from each top target point in an oblique direction to the center, draw lines. The pattern should resemble a parquet. That is, two triangles should appear in the drawing. From the acute angle of the upper triangle, a line is drawn to the lower triangle. The planned lines are cut and expanded to the desired width. Draw a drawing around the outline.

Other types of sleeves "flashlight"

Fantasy and imagination is the main principle of every fashion designer. Elegant sleeves can be made in various ways. You can perform assembly only in the center of the shoulder bend. Instead of assembling, you can make several creases. On the basis of the drawing, you will need to draw two lines: horizontal and vertical. The vertical line is drawn from the shoulder bend, and the horizontal line is drawn along the lines of the axillary basins. These lines are cut. In the drawing you should get two triangles. Now we need to move them in different directions, but do not take away from the points of the armpits. The point on the humeral fold is extended, and the triangles will rise from the horizontal line. Such a sleeve is called "with a raised head". There will be an assembly on the pellet, and the bottom - you can simply bend it or process it with a cuff or cuff.

Thus, it can be concluded that the pattern of the flashlight sleeve can be made by yourself, and if there is a drawing of the base on hand, then, showing imagination and ingenuity, you will get a unique outfit. But we must remember the familiar advice from tailors, which must be measured seven times and cut off once. Thinking over the model of the flashlight sleeve, you should first calculate everything carefully on paper, and only then cut out on the fabric.