Pellet burner with own hands: manufacture

Recently, consumers consider it justified to purchase all kinds of heating devices that are able to function on an alternative fuel. Thus, the popularity of pellet burner, its own hands can be made quite simply. Such a design can be installed without much difficulty, and during operation it shows its positive characteristics. In particular, this approach is relevant in the place where there is no gas pipeline, and electricity is a fairly expensive resource. As the main minus of such a boiler is quite impressive value, which is true for factory models. That's why the masters recommend making such a heating device yourself. If necessary, then in return for the mentioned fuel, coal, firewood and other vegetable wastes can be used. If a pellet burner is produced by hand, it is important to consider its additional advantages.

Positive features

The described equipment has an automatic ignition system, and is also fireproof. The consumer will be able to reduce costs due to the low cost of pellets. Among other things, the service does not need to spend additional funds. You can count on a high coefficient of efficiency, and the period of operation of such equipment is 20 years, which will depend on the correctness of production and operational characteristics. The device does not depend on central heating sources and tariffs for such services.

Production of pellet boiler

If the pellet burner with its own hands, the drawings of which are presented in the article, will be produced independently, then at first glance this design may seem unnecessarily complicated. However, if there is a desire, then all the work can be done independently. To do this, you will need to pick up tools and materials, as well as buy additional components.

Preparatory work

The pellet burner can not be produced without the main component of the same name, which is recommended to be purchased at the store. This is due to the fact that the burner itself has a rather complex design, and to produce it independently, although there is an opportunity, but such manipulations are difficult to implement. The burner is an element where the fuel is ignited, but with it, the intensity of the flame is also regulated. Among other things, the design will be sensors and programmers, which allow for more economical fuel consumption. With the help of these elements, it will be possible to achieve a comfortable indoor temperature. The pellet burner must have a housing that is recommended to be placed horizontally. This will allow the most efficient use of heat extracted from the combustion of fuel. In the role of material for the formation of the hull, sheet steel can act, but experts sometimes advise using cast iron or bricks. You can give preference to the material that, in your opinion, is able to retain heat longer. The enclosure must provide a quality heat transfer to the next element of the device, i.e. the heat exchanger.

Recommendations of a specialist

The pellet burner must have a heat exchanger, which is located inside the shell. It has the appearance of several pipes, which are sometimes replaced by a coil. They are connected to the heating system of the building. Among other things, you should provide an inlet for pouring cold water. When preparing the combustion chamber, it is necessary to provide an opening in it, the diameter of which should be equivalent to the parameters of the burner purchased. A 100-mm screw and electric motor will work in tandem. The latter must be connected to the device control unit.

Technology of work

If a pellet burner is produced with their own hands, the drawings of which are presented in the article, then an inlet nozzle must be installed in the unloading neck of the tank, which refers to the screw. Afterwards, on its other part, a plastic pipe is fixed, along which the burner granules run. When a signal is received, the engine starts and continues to operate until the combustion chamber is filled with the right amount of heat.

Features of work

The device of the pellet burner assumes the presence of an even powerful torch, which is necessary for heating the water jacket. The intensity of the flame can be adjusted. To ensure the supply of husks and pellets, a screw conveyor should be used, while fuel in it will come from the hopper. The volume of the latter should be determined by how long the device will last. It is important to equip the structure with a fan that will pump air into the combustion area. You can make pellet burner drawings yourself. It is important to take into account the expected size. For example, the combustion chamber may have both a circular and a rectangular section. The first variant is encountered somewhat more often, since manufacturing in this case is simpler. A flat fuel pan is installed in the round chamber, while the camera itself is fixed to the flange plate. The latter should be adjacent to the front of the device from the outside.