"Kalmatron": specifications and description

"Kalmatron", the technical characteristics of which will be described below, is a protection for building materials and structures from water permeability, man-caused and climatic corrosion, as well as other environmental influences. The composition can be used to protect new buildings and new buildings.

Description

Waterproofing "Kalmatron", the technical characteristics of which must be studied by the consumer before purchasing the product, has many advantages. Among them, an attractive quality-price ratio should be highlighted.

The composition of "Kalmatron" is easy to use, it is explosive, fireproof and non-toxic. Among other things, Kalmatron enterprises are located in different regions, they are in close proximity to the main consumers, which ensures compliance with delivery schedules in any volumes. At the same time, transportation costs can be minimized. The composition of "Kalmatron", whose technical characteristics are unique, is resistant to mechanical influences, it is effective at reverse and direct high hydrostatic pressure.

Scope of use

With the help of the "Kalmatron" composition it is possible to effectively eliminate leaks, restore the waterproofing properties of the foundation surfaces, which consist of foam, aerated concrete, concrete, reinforced concrete, brick, concrete and quarry stone. To carry out the work on waterproofing can be in the process of operation or at the stage of construction. Structures after processing receive the qualities of increased frost resistance, since their structure becomes less porous. Automatic suction and water intake are reduced, and the strength characteristics are increased, as are their bearing capacity. Use the waterproofing "Kalmatron" can be on sites where the level of acid-base balance is in the range of 3 to 11.

Features of composition use

Waterproofing "Kalmatron", the technical characteristics of which are described in the article and will allow you to exclude mistakes during the work, should be applied to the prepared surface. To do this, the base is cleaned with a mechanized tool or metal brushes, while removing the layer of plaster, cement and dense film or paint. It is necessary to rid the base of the destroyed layer of brick or concrete, as well as other contaminants. Chemical milling will remove the cement film from the surface. If there is on the basis of a crack, then they need to be divided into a cone, going down about five millimeters. Their base is peeled off, and then a protective coating is applied. The surface must be dry at the same time.

Technical characteristics of waterproofing "Kalmatron"

"Kalmatron", the technical specifications and description of which will help you make the right choice when buying waterproofing, is a gray powder with whitish inclusions. Its moisture content by mass does not exceed 1%. When closing the solution with the use of the "Kalmatron" composition, it is important to remember that the beginning of setting will occur not earlier than in ten minutes, while the end of setting should be expected no later than 85 minutes. After 28 days strength will reach 28 MPa. Consumers may also be interested in the density, which will be observed after 28 days, - it is 2,400 kg / m3. When working with the "Kalmatron" composition, you should also know about water and gas resistance, the value of which varies in the range from 0.8 to 2.4 MPa. Using this product, the strength of the structure will be increased by 27% or less. "Kalmatron", technical characteristics, the description of which is important to know before purchasing the product, increases the concrete brand by frost resistance by 35%.

Technical characteristics of the composition "Kalmatron-D"

In appearance, the composition is a loose powder of gray color. Humidity by weight does not exceed 1%, and the average bulk density is equivalent to 1300 kg / m ³ . This value can be increased or decreased by fifty positions. Water resistance of the material will be increased by several positions, from 2 to 4, if you add this mixture when the solution is closed. Professionals are also interested in such a characteristic as the coefficient of sulfate resistance, it can be as low as 0.92.

Features of waterproofing of the brand "Kalmatron-D"

"Kalmatron-D", whose technical characteristics are recommended to study before use, is intended to increase the strength of concrete to 20%. The number of cycles of frost-resistance of the concrete structure will be increased by 50 if the concrete is added to this concrete. In addition, thanks to the addition of "Kalmatron-D", the lifetime of reinforced concrete structures is increased by a factor of 1.5 compared to conventional concrete.

"Kalmatron-Econom"

"Kalmatron-Econom" is intended to reduce the overspending of the composition, when its application is provided on the surface of a large area. In appearance, this composition is a gray powder with white inclusions. Humidity by weight does not exceed 0.1%. The beginning of grasping can occur in thirty minutes. Frost resistance of the composition is equivalent to 200 cycles, but the tensile strength at bending is 3 MPa.

For reference

If the master wants to cover a fairly large thickness, which is especially true for brickwork as a roughing base, then the "Kalmatron-Econom" composition, whose technical characteristics have been described above, should be used. It is suitable for filling cavities, as well as strob. When horizontal screeds are installed of impressive thickness, to improve performance and surface strength, iron should be used with the help of the "Kalmatron" composition. The flow rate can vary from 1.5 to 1 kg / m ² . The base is ground by a plastic or metal tool.

Depending on the desired results, you can choose the composition that is right for you.

Recommendations for the care of the coating

If you are interested in the waterproofing "Kalmatron", the technical characteristics of which are presented in the article, then you should also know how the coating is carried out. After application, the substrate must be kept in wet conditions for twelve hours. To do this, the surface is wetted with an interval of four hours. To display higher protective properties, the coating should be allowed to ripen in damp conditions. Leave the surface for three days, this is especially important for bases that will be used outdoors or in conditions of alternating wetting and drying. The applied coating must be carefully moved, only in this way you will get a guaranteed result. Before purchasing a mixture, one can familiarize with its consumption. So, per square meter will take about 1.6 kilograms, if the thickness of the layer will be equal to one millimeter.