How to knit a knitted knitting needle?

When a beginner needlewoman first encounters knitting, she has a lot of questions. For example, how to choose yarn, tools, where to start. More experienced craftsmen are interested in learning how to get knitted with knitting needles. All these questions will be raised in the article presented.

How to start a beginner?

It is clear that an experienced needlewoman will not tell her budding girlfriend what nakid knitting, how to knit it and why it is needed. Perhaps, it can be left for later. To say which thing to knit first, is quite difficult. Each needlewoman has a different level of skill, patience, attentiveness and accuracy. It is very important that the first experience in knitting does not cause any irritation, otherwise the desire to engage in such a craft will disappear for a long time.

It is recommended to study special literature, read master classes for beginners, consult a person who has been doing needlework for a while. In any case, you have to practice a little hitching, learn to knit the front and back, close the row and only then go to more complex patterns. The first thing you can make with knitting needles can be a simple scarf, a jumper or a pillow case. It's important to start, get pleasure from it and develop your skills.

Selection of yarn

When knitting, it is important to select the correct thread. For knitting needles yarn of any thickness and with different components. It is advisable to buy more threads than indicated in the scheme. This is due to the fact that each pattern will require a different amount of yarn, so to anticipate the expense is quite difficult.

When choosing a consumable, it is important to pay attention to the twisting of the threads. If they are too tightly woven, then the stocking can be slightly mowed. To check this, you need to unwind a piece of 100 cm long thread, put the beginning and the end together. If the loop lazily twists 2-3 times, then the canvas, connected with a stocking pattern, will not mow. If the thread is energetically folded more than 10 times, then such a yarn should not be chosen for such a rapport to avoid skewing. Perhaps, if one of the components of the pattern is a knitting needle, then you will avoid such a problem.

Also, the yarn should be checked for resistance to staining. To do this, take a piece of white cloth, fold it into a roll, on top of which the necessary thread is wound (20-30 cm). So you can do with all the samples of yarn that will participate in knitting. Rolls of fabric should be washed and dried in a folded state. Then you need to unwind the threads and make sure that they do not leave any traces after washing.

Selection of knitting needles

Knitting needles (knitting needles) for knitting can be divided into two categories: by shape and by material.

In form this tool is divided into:

• Circular (circular);
• Direct.

The main materials for making knitting needles are:

• Metal (aluminum, steel, duralumin);
• plastic;
• bamboo;
• tree;
• bone.

The toolkit should not be rough. Its surface should not contain a notch, as this will interfere with knitting. Create a variety of patterns with knitting needles on any tool. The main thing is that the thread slips easily and without difficulty.

All spokes are divided into numbers from 1 to 20. According to the experts, it is rather difficult to work with thick tools because of the fast-onset fatigue of the hands.

In addition to the spokes, additional elements are used in the work:

• Vintage loops;
• Short curved spokes;
• Loop holders or pins for the removal of unclosed stitches;
• Counters of rows;
• Caps for long spokes.

Preparing yarn for work

In order to make the canvas beautiful, and some elements, for example, nakid knitting needles, at work did not cause difficulties, craftsmen prepare yarn. It is important to do this correctly, to rewind the consumables in the morning. It is advisable to wash the threads, dry and coil. What is this for? In order to determine in the processing process how the thread will behave: it will stretch, deform or shrink. After washing and drying during the process, the thread will not produce undesirable results.

It is most convenient to work when the yarn is wound on a bobbin or a Bulgarian tangle. It is recommended to pull the thread from inside the skein.

If the yarn from one coil has ended, then it is recommended not to tie the end of the old reel into the knot and start a new one, but lay one on top of the other and tie several loops together. To avoid thickening in this case, skilled craftsmen advise to untwist the endings of threads and only then to superimpose one on another. After the item has been created on the wrong side, the "traces" data should be attached.

Loosening of the front and back loops

Finally, the conversation approached the immediate beginning of the work. Before you make any product, you need to know how to perform the front and back, removed and extended hinges, nakid spokes.

After the beginning needlewoman has prepared the original row, she should take off the first stitch and do not tie it. The thread is located on the index finger of the left hand. The right needle is inserted into the second loop, grasps the yarn, pulls it through the stitch, which immediately descends from the left stocking needle. It turns out that the newly appeared element remains on the right side. Similarly, you should knit to the end of the row.

Advice from experienced craftsmen: do not tighten the hinges too tightly. It is better if the mating is medium density. Tight loops are difficult to pull. And too loose stitches look ugly on the finished canvas.

With the back weaving, the working thread is placed before the blade on the index finger. The right needle is inserted from the back side into the second stitch (the first is removed), yarn is caught. With the help of the index finger of the working hand, it is necessary to stretch the thread through the loop and leave it on the main stocking needle. The series is fully extricated.

Closing loops

To prevent the canvas from blooming, after finishing work on it, it is necessary to close the working loops. There are 2 common ways to fix stitches:

1. To knit together 2 loops according to the drawing. One stitch is obtained, which goes to the previous spoke. By circulating 2 loops together and leaving the resulting new element to the left, the master will close the entire row completely.
2. It is necessary to remove the edge loop. Next, tie a pattern. The left spoke to pass over the resulting stitch on the right side to the edge, grab it. With the right stocking needle, stretch the second loop through it and leave it in its original position.

Stitch the next stitch along the picture. Repeat the actions to "capture" the first loop and return it to the left spoke. Making such alternate manipulations with stitches, the needlewoman can close the entire row. It does not matter, if in the last row there was a facial mantle, it will be possible to fasten the hinges with knitting needles without harming the knitted fabric.

Unscrewing the crochet

After gaining the skills to create the front and back stitches, the needlewoman moves on to the next stage. Now a beginner skilled worker will understand how to make a knitted knitting needles and tie a unique pattern. Typically, similar techniques are used to create a delicate and patent pattern, a cloth with elongated stitches and a complex weave of threads.

There are such loops "to themselves" and "from themselves":

1. Reverse cape. In another way, it is called "to yourself." In this case, it is necessary to pass the end of the main knitting needle under the working thread and to grab the yarn from the right to the left.
2. Straight Cape. Otherwise it is called "from yourself". The end of the main knitting needle passes over the working thread and from the left to the right is threaded with a loop.

The face stitch with such manipulations is easily bonded. The original should be held with a finger, so that the loop does not come off in the process of work.

How to knit a loop with a knitted needles - it's easy to understand. The main thing is to practice this technique in practice.